Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
maximum. 2. Connect to 100 psi maximum shop air. 3. Keep safety bar in position at all times - except when lowering. 4. Keep hands and tools from under carriage. 5. Do not mount table when in elevated position. 6. Do not ride vehicle onto lift. 7. Lift must be in the lowered position when moving. 8. Only trained persons should operate Air Lift. 9. The working area should be sufficiently lit. 10. Foot controller should be at least 3 feet away from Air Lift during raising and lowering operation. HANDY INDUSTRIES L.L.C. 702 South 3rd Ave. Marshalltown, IA 50158 1-800-247-7594 Fax 641-752-1205 GRUNTAVORE LIFT NOTE: READ ENTIRE MANUAL TO COMPLY WITH ALL SAFETY AND SERVICE PRE- CAUTIONS. DEATH, PERSONAL INJURY AND/OR PROPERTY DAMAGE MAY OCCUR UNLESS INSTRUCTIONS ARE FOLLOWED CAREFULLY. INSTRUCTIONS UNPACKING AND SET-UP 1. Open carton, then remove ramp and shipping boards. 2. Connect foot-operated air valve to 100 psi maximum air supply. The lift may be damaged and/or personal injury may result if the pressure exceeds the maximum 100 psi rating. 3. Stand clear of lift table, and depress the UP side of foot valve to raise table. 4. To lower table, lift detent bar from safety latch and lower to next position or to floor. 5. To mount ramp, insert ramp mounting pins into holes at end of table opposite vise holes. UNPACKING AND SET-UP OF EXTENSION COMPONENTS 1. Open cartons containing side and end extension components. Refer to the illustration and parts list page. 2. Connect Air Lift to 100 psi air then raise lift and engage safety detent bar. 3. Insert the 53-1/4” stabilizer shafts thru each frame end. Place axle extensions with the wheels secured by two spiral retaining rings onto shaft then retain with quick pins. Place stabilizer feet onto shaft at outside frame and retain with quick pins. 4. Insert the two 3/4” pipes thru holes near center of lift top. Place side extensions onto these pipes and retain with quick pins at each end of the pipe. 5. Pull side extensions out against quick pins and center side extensions on the Air Lift. 6. Place end extension onto lift top and side extensions aligning pipe holes , then insert 1” pipe. Install quick pins at pipe ends. Secure end extensions to both lift top and side extensions to both lift top and side extension using ten 5/16-18 cap screws and nuts for each end extension. Note eight bolts go down and one is located at each side near bend. 7. Attach detent handle extensions on each side of detent safety bar. See detail on illustration and parts list page. 8. To mount ramps, insert mounting pins in to matching slots on the end extension farthest from the wheels of the Air Lift. OPERATION 1. Loads must be centered on table at all times. Table is rated for a maximum load of 1800 lbs. 2. Loads must be firmly positioned and secured on table at all times. 3. All moving parts have been lubricated at the factory and should be re-lubricated every (6) months to prevent galling. Grease zerks are located at each end of frame pivot shaft and at top ends of inside frame assembly. 4. Lightly oil cylinder rod when it becomes dry. 5. Squirt some oil through bleed hole in plate end of cylinder to lubricate piston and its seal every (6) months. 6. Pivot shaft set screws should be checked frequently to be sure they are tight. These are located at the top end of the inside frame assembly. GRUNTAVORE LIFT MOUNTING ILLUSTRATION AND PARTS LIFT PART NO.. DESCRIPTION QTY 11253 SPIRAL RETAINING RING 4 11271 10-32 HEX NUT 2 11358 QUIK PIN 12 12128 5/16-18 X . HEX HD CAP SCREW 20 12305 5/16-18 HEX NUT 20 14737 CAST WHEEL 2 15255 DETENT HANDLE EXTENSION RETAINER 2 15258 DETNET HANDLE EXTENSION TUBE 2 15261 SWIVEL STABILIZER FOOT 2 15263 AXLE EXTENSION 2 15265 STABILZER SHAFT 53 .” 2 15267 .” PIPE EXTENSION 61 .” LONG 2 15269 1” PIPE EXTENSION 61 .” LONG 2 15275 END EXTENSION ASSEMBLY 2 15452 RAMP ASSEMBLY (ONE COMES WITH 16865) 1 15618 SIDE EXTENSION 2 16865 LIFT GRUNTAVOR 1 GRUNTAVORE PARTS DRAWING - PARTS LIST Part # Description 10819 detent clip 14381 air hose assembly 11250 screw 3/4 -10 x 1-3/4 11253 retaining ring 1-5/16 11255 lockwasher - 3/4” 14737 wheel 12887 valve stem assembly 12937 foot valve assembly complete 11304 cylinder shaft bushing 11305 cylinder shaft seal 16764 cylinder assembly 15397 cam roller bearing 16765 cylinder shaft assembly 15400 retaining ring 2-3/8” 15401 piston Part # Description 15403 piston seal 15253 top assembly 16761 inside frame assembly 16760 outside frame assembly 16766 foot assembly 15452 ramp 15687 drop out cover 15458 detent bar 15460 frame pivot shaft 15461 cylinder pivot shaft 15462 retaining ring 1-1/4” 15463 track roller bearing 15484 cover plate 15528 rubber pad 15529 spacer LIFT LIMITED WARRANTY Handy Industries, LLC, warrants to the original purchaser of this Air Lift, all parts to be free from defects in manufacture for a period of ninety days from date of delivery. Notice of defective part must be received in writing at Hand...