Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
• Do not stand or sit on the speakers. You may be injured. Using other subwoofer You can connect a subwoofer with an amplifier to the SUBWOOFER PREOUT socket. This unit’s rear panel SUBWOOFER PREOUT LINE IN L R ANTENNA DAB/FM To audio input socket Audio cable (commercially available) Commercially available subwoofer (amplifier built in) Note • No sound is heard from the subwoofer without a built-in amplifier. • Subwoofer Pre-out (audio signal): 350 mV / 10 k ..at 70 Hz. Connecting antennas Connect the DAB/FM wire antenna as shown below. To improve reception and sound quality, connect external antennas (see Using external antennas below). ANTENNA DAB/FM 1 1 Connect the DAB/FM wire antenna into the DAB/FM antenna socket. For best results, extend the DAB/FM antenna fully and fix to a wall or door frame. Don’t drape loosely or leave coiled up. To customers in Norway and Sweden CAUTION • “Apparater som er koplet til beskyttelsesjord via nettplugg og/eller via annet jordtilkoplet utstyr - og er tilkoplet et koaksialbasert kabel-TV nett, kan forarsake brannfare. For a unnga dette skal det ved tilkopling av apparater til kabel-TV nett installeres en galvanisk isolator mellom apparatet og kabel-TV nettet.” • “Apparater som ar kopplade till skyddsjord via jordat vagguttag och/eller via annan utrustning och samtidigt ar kopplad till kabel-TV nat kan i vissa fall medfora risk for brand. For att undvika detta skall vid anslutning av apparaten till kabel-TV nat galvanisk isolator finnas mellan apparaten och kabel-TV natet. Using external antennas To improve DAB/FM reception Use a PAL connector (not supplied) to connect an external DAB/FM antenna. ANTENNA DAB/FM One-touch PAL connector 75 ..coaxial cable En Connections Connections Plugging in CAUTION • Do not use any power cord other than the one supplied with this unit. • Do not use the supplied power cord for any purpose other than that described below. Before making or changing the connections, switch off the power and disconnect the power cord from the AC outlet. After you’ve finished making all connections, plug the unit into an AC outlet. This unit’s rear panel AC I N To AC outlet Power cord SPEAKER R En Getting started Getting started Chapter 4: Getting started To turn the power on Press the . STANDBY/ON to turn the power on. After use: Press the . STANDBY/ON to enter the power stand-by mode. Note • In standby mode, if iPod/iPhone/iPad is connected, the unit turns charge mode. Setting the clock STANDBY/ON .. CD USB TUNER AUDIO IN 1 2 3 BT AUDIO CLOCK/TIMER SLEEP EQUALIZER OPEN/CLOSE DISPLAY FOLDER MENU PRESET VOLUME TUNE– TUNE+ MEMORY /PROGRAM ENTER 1 Press . STANDBY/ON to turn the power on. 2 Press CLOCK/TIMER on the remote control. “CLOCK” is shown on the main display. 3 Press ENTER. 4 Press ./. to set the day, then press ENTER. 5 Press ./. to set the hour, then press ENTER. 6 Press ./. to set the minute, then press ENTER to confirm. 7 Press ENTER. To confirm the time display: Press the CLOCK/TIMER. The time display will appear for about 10 seconds. To readjust the clock: Perform “Setting the clock” from step 1. Note • When power supply is restored after unit is plugged in again or after a power failure, reset the clock. General control Input function When the INPUT on main unit is pressed, the current function will change to different mode. Press the INPUT repeatedly to select desired function. CD FMDAB USB/iPod Display brightness control AUDIO IN LINE BT AUDIO Press DIMMER to dims the display brightness. The brightness can be controlled in four steps. Volume auto setting If you turn off and on the main unit with the volume set to 31 or higher, the volume starts at 30. Volume control Turn the VOLUME on the unit or press VOLUME +/– on the remote control to increase or decrease the volume. CAUTION • The sound level at a given volume setting depends on speaker efficiency, location, and various other factors. It is advisable to avoid exposure to high volume levels. Do not turn the volume on to full at switch on. Listen to music at moderate levels. Excessive sound pressure from earphones and headphones can cause hearing loss. Muting The volume is muted temporarily when pressing the MUTE on the remote control. Press again to restore the volume. En Getting started Getting started Sound controls Equalizer When the EQUALIZER is pressed, the current mode setting will be displayed. To change to a different mode, press the EQUALIZER repeatedly until the desired sound mode appears. FLAT A flat and basic sound. A powerful sound that ACTIVE emphasizes low and high tones. A sound that allows the radio or DIALOGUE vocals to be heard more easily. A sound that can be enjoyed NIGHT at night even with lower volume. P.BASS control When the power is first turned on, the unit will enter the P.BASS mode which emphasises the bass frequencies. To cancel the P.BASS mode, press the P.BASS on the remote control. Bass/treble control Press the BASS/TREBLE, then press ./././. to adjust the bass...