Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
The best result is achieved when all speakers have equal volume in the listening position. 4 Press TEST TONE on the remote control. y The test tone stops. Note: If you are not completely satisfied with the volume settings, we recommend making minor adjustments to them during surround sound playback. Power handling If the receiver is used at very high power it can produce distortions which may damage your speakers seriously. If distortions occur, reduce the volume and the tone controls to a level where the sound is acceptable again. To avoid overheating of the unit a safety circuit has been built in. Therefore your set may disconnect under extreme conditions. If this happens, switch the unit off and let it cool down before reusing it. Headphones Connecting headphones to PHONES will switch off the speakers. The receiver switches to STEREO and surround sound will be reduced to a stereo signal which is reproducible by standard headphones. Disconnecting the headphones switches on the speakers again. If you wish to enjoy surround sound again, switch the receiver back to surround sound. Maintenance Clean the receiver with a soft, slightly dampened, lint-free cloth. Do not use any cleaning agents as they may have a corrosive effect. Do not expose the receiver to humidity, rain, sand or excessive heat (caused by heating equipment or direct sunlight). 14 SUBWOOFER (MX 960D, MX 980D only) Connections Controls SPEAKER OUT IN + + + + - - - - ACMAINS~ SOURCESELECTOR SPEAKER IN / WIRELESSSUBWOOFER IN SUBWOOFER IN PHASE SELECTOR 0° 180° CUT OFF FREQUENCY 60 Hz 150Hz SUBWOOFERLEVEL CONTROL STANDBY -ON MIN MAX HIGH POWER SUBWOOFER 1 2 3 4 5 6 7 8 9 0 1 STANDBY-ON y............Switches the subwoofer on and to standby. 2 ..........................................Status light. 3 CUT OFF FREQUENCY...Adjusts the frequency range reproduced by the subwoofer. 4 SUBWOOFER LEVEL CONTROL Adjusts the volume of the subwoofer. Connectors 5 PHASE SELECTOR .........Selects the best bass reproduction. 6 SUBWOOFER IN ............Connect to SUBWOOFER PRE-OUT at the receiver. 7 SOURCE SELECTOR ......Selects the used signal input. Keep at the SUBWOOFER IN position if the receiver is connected as described below. 8 AC MAINS ......................After all other connections have been made, connect the power cord to AC MAINS and to the power outlet. 9 SPEAKER OUT ...............Not used with the receiver supplied. 0 SPEAKER IN ...................Not used with the receiver supplied. The type plate is located on the rear of the subwoofer. 1 Use the cinch cable supplied to connect SUBWOOFER IN to SUBWOOFER PRE-OUT at the receiver. 2 Check whether the power voltage as shown on the type plate corresponds to your local power voltage. If it does not, consult your dealer or service organization. 3 Connect the power cable to the power outlet. This switches on the power supply. Do not connect the subwoofer to the outlets of the receiver. Note: To disconnect completely the subwoofer from the power, remove the power plug from the power outlet. Adjustment The subwoofer must be adjusted to your listening environment and to your speaker setup. This only needs to be done once. 1 Press y to switch on the subwoofer. yThe status light turns green. 2 Play one of your favorite tracks at a normal listening level. 3 Turn SUBWOOFER LEVEL CONTROL to adjust the volume of the subwoofer. 4 Select the reproduced frequency range by turning CUT OFF FREQUENCY. The higher the cut off frequency is set, the stronger the bass reproduction will be. Note: The subwoofer reproduces the range between 35 Hz and the frequency selected with CUT OFF FREQUENCY. 5 You may switch PHASE SELECTOR from 0° to 180°. Select the setting that provides the sound that produces the bass effect. 6 Press y to switch the subwoofer to standby. yThe status light turns red. Operation 1 Press y to switch on the subwoofer. yThe status light turns green. 2 If the sound reproduction is noisy, reduce the volume of the subwoofer. 3 Press y to switch the subwoofer to standby. yThe status light turns red. English 15 16 English DISPLAY The display of the receiver is divided into 4 sections, which are to be used for the following: Speaker diagram A rectangle with a letter in it shows that a speaker has been selected in the setup menu. However, the subwoofer indicator will only light when a subwoofer signal is available. If only a letter is shown, this speaker is not used and its sound is being reproduced by the other speakers. .....virtual surround sound SURROUND.................surround sound is reproduced DIGITAL SURROUND ....digital surround sound is reproduced L, R ...........................front left and right speaker C...............................center speaker SL, SR .......................surround speakers SW............................subwoofer Menu indication These signs show you if the menu is on or off and indicate in which direction you may move. MENU .......................Menu is on. 1......................