Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
The respective speaker indicators lights up on the front panel display. 3 Press NINPUT l / h repeatedly (or press one of the input selector buttons (e)) to select the desired input source. The name of the currently selected input source appears on the front panel display for a few seconds. Available input source INPUT:DVD Currently selected input source 4 Start playback on the selected component or select a broadcast station. Notes • Refer to the operating instructions for the source component. • See page 27 for details about FM or AM tuning instructions. y • To adjust the level of each speaker, see page 20. y • See page 20 to adjust the level of each speaker. • This does not affect the AUDIO OUT (REC) level. • You can set the initial volume level and maximum volume level (see page 34). 6 Press LPROGRAM l / h (or press uPROG l / h) repeatedly to select the desired sound field program. The name of the selected sound field program appears on the front panel display. See page 22 for details about sound field programs. Movie Dramatic Currently selected surround field program Notes • Choose a sound field program based on your listening preference, not merely on the name of the program. • When you select an input source, this unit automatically selects the last sound field program used with the corresponding input source. • Sound field programs cannot be selected when the component connected to the MULTI CH INPUT jacks is selected as the input source (see page 19). • When PCM signals with a sampling frequency higher than 48 kHz are input, this unit is automatically set to the “STRAIGHT” mode (see page 26). • To display information about the currently selected input source on the front panel display, see page 21 for details. 18 En Playback Guide to contents When you want... See page Adjust the tonal quality of the front 20 speakers Edit parameters of sound field 26 programs Enjoy the sources which have wide 20 dynamic range at night Use headphones 20 Select a decoder to play back 26 sources with Set this unit to the standby mode 21 automatically Additional operations Using input setting features Use the following features to select input jack or input source. ¦ Selecting the front speaker set Press CSPEAKERS repeatedly change the active front speaker set that is connected to the FRONT A or FRONT B speaker terminals or turn off the front speakers. The active front speaker set changes as follows: FRONT A FRONT B OFF Note • Turn off the volume level of this unit before you switch the front speaker setting. ¦ Using the Zone B feature When you set “FRONT B” to “ZONE B” (see page 32), you can use the speakers connected to FRONT B speaker terminals in another room (Zone B). Press CSPEAKERS on the front panel repeatedly to turn on or off the Zone B speakers. When you activate the Zone B speakers, all the speakers in the main room are muted. Notes • You cannot activate both the main room and Zone B speakers simultaneously. • If you select CINEMA DSP sound field program and activate the Zone B speakers, Virtual CINEMA DSP is activated automatically (see page 26). ¦ Selecting the component connected to the MULTI CH INPUT jacks as the input source Use this feature to select the component connected to the MULTI CH INPUT jacks (see page 14) as the input source. Press NINPUT l / h repeatedly (or press fMULTI CH IN) to select “MULTI CH.” “MULTI CH” appears on the front panel display. y • You can configure the multi channel input settings in “MULTI CH” (see page 35). Notes • Sound field programs, or the night listening mode, etc. cannot be selected when “MULTI CH” is selected as the input source. • When headphones are used, signals are output only from the front left and right channels. ¦ Selecting audio input jacks (AUDIO SELECT) Use this feature (audio input jack select) to switch the input jack assigned to an input source when two or more jacks are assigned to an input source. y • We recommend that you set the audio input jack select to “AUTO” in most cases. • You can adjust the default audio input jack select of this unit by using “AUDIO SELECT” in “OPTION MENU” (see page 36). 1 Press NINPUT l / h repeatedly (or press one of the input selector buttons (e)) to select the desired input source. 2 Press nAUDIO SEL repeatedly to select the desired Audio input jack select setting. A.SEL:AUTO DVR DVD CD V-AUX DTV/CBL MD/CD-R TUNER Audio input jack select setting Choice Function AUTO Automatically selects input signals in the following order: (1) Digital signals (2) Analog signals ANALOG Selects only analog signals. If no analog signals are input, no sound is output. y • You can configure the audio input jack select setting in “AUDIO SELECT.” Note • This feature is not available if no digital input jack is assigned to the selected input source in “INPUT ASSIGN” (see page 34). BASIC OPERATION English 19 En Playback Using audio features Use the following features to adjust the audio output or speaker level. ¦ Muting the audio output Pre...
Dieses Handbuch ist für folgende Modelle:Heimkino-Systeme - YHT-292 (2.04 mb)