Stimmen - 4, Durchschnittliche Bewertung: 4.8
(
)
)
|
Anleitung Zusammenfassung
Subwoofer: On the floor. The position of the subwoofer is not so critical because low bass tones are not highly directional. Amplifier unit Subwoofer Right front speaker Left front speaker Right surround speaker Left surround speaker Center speaker EnglishEnglish . Adjusting the front angle of the satellite speakers The front angle of the satellite speakers can be adjusted as shown below. 1 Loosen the screw on the bottom of the speaker stand. * Attach the supplied nonskid pads at the four corners on the bottom of the stand for improved stability. . Placing a center speaker on top of the monitor When placing the center speaker on top of the monitor, remove the stand from the speaker, and attach the provided fastener at the bottom of the speaker and on top of the monitor to prevent the speaker from falling. * Do not place the speaker on top of the monitor with an inclination of more than 10 degrees. Pads 2 Adjust the speaker angle on the stand as you prefer, and then tighten the screw. 10& 10&Fastener . Mounting satellite speakers on a wall The satellite speakers can also be hung on the wall. Fasten screws into a firm wall or wall support as shown in the figure, and hang the slits on the rear of the speaker on the protruding screws. * Make sure that the screws are securely caught by the slits. Tapping screw (4 mm) (Available in hardware stores) 50 mm Min. 20 mm 4 mm Wall/ wallsupport Warning . Each speaker weighs 0.4 kg (0.9 lbs.). Do not mount them on thin plywood or a wall with soft surface material. If mounted, the screws may come out of the flimsy surface and the speakers may fall. This could damage the speakers and cause personal injury. . Do not install the speakers on a wall with nails, adhesives, or any other unstable hardware. Long-term use and vibrations may cause them to fall. . To avoid accidents resulting from tripping over loose speaker cords, fix them to the wall. Note Though this speaker is a magnetically shielded type, there may be some influence on the monitor picture depending on the type of monitor or the placement of the speaker. In such a case, place the speaker further apart from the monitor until there is no influence on the monitor picture. . Mounting the amplifier unit on the supplied stand For improved stability, it is recommended to mount the amplifier unit on the supplied stand with the supplied screws as shown below. * Attach the supplied nonskid pads at the four corners on the bottom of the stand for improved stability. Pads To front E-5 Connections Connections (See figure 1 on page IV.) Caution: Plug in the amplifier unit and other equipment after all connections are completed. A : Connect the three satellite speakers with a 3 m cord to the FRONT L, R and CENTER terminals. Connect the two satellite speakers with a 7 m cord to the SURROUND L and R terminals. Connect the subwoofer to the SUBWOOFER terminal. B : Connect external audio/video units (a personal computer, a video game player, a portable DVD/CD player, a video cassette player, etc. which send playback signals to this system) to these terminals. Cautions . When placing the provided AC adaptor on the desk, etc., be sure to fix the adaptor on the desk, etc. to prevent it from falling. If the adaptor falls, it may cause personal injury or damage to the adaptor and/or other equipment. . The SPEAKER OUTPUT terminals on the rear of the amplifier unit are only designed for connection of the supplied speakers. Never connect these terminals to an AV amplifier or a power amplifier, as it may cause misoperation, fire and/or damage to this system. Controls & connectors (See figure 2 on page IV.) 1 INPUT selector button and indicators Press this button repeatedly to select an input mode between DIGITAL, 4CH and 2CH. The current mode is shown by the lighting of the corresponding indicator. DIGITAL: Select this mode to reproduce signals received at the OPTICAL or the COAXIAL terminal on the rear panel. When both OPTICAL and COAXIAL terminals receive signals, the signals at the OPTICAL terminal are selected. 4CH: Select this mode to reproduce signals received at the analog input FRONT and SURROUND terminals on the rear panel in 4-channel surround sound mode. (The center speaker is not used in this mode.) 2CH: Select this mode to reproduce signals received at the analog input FRONT terminal on the rear panel. (The PROLOGIC surround mode can be used in this mode.) 2 MODE selector button and indicators Press this button repeatedly to select the desired surround mode between on (DTS, DIGITAL, PROLOGIC) and off. The current mode is shown by the lighting of the corresponding indicator. * If a DTS or Dolby Digital encoded signal is inputted when the surround mode is off, the corresponding indicator lights up dimly. DTS: Select this mode to reproduce a DTS encoded input source. This mode can be selected only when the input signal is encoded with DTS and the input mode is set to DIGITAL. DIGITAL: Select this mode to reproduce a Dolby Digital en...