Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
SETUP. If you do not operate the remote for a few seconds, the parameter disappears from the display and is stored in the system. xSIZE When you do not connect center or rear speakers, or move the rear speakers, set the parameters for CENTER and REAR. Since the front speaker and subwoofer settings are fixed, you cannot change them. The default settings are underlined. • CENTER (center speaker) – YES: Normally select this. – NO: Select this if no center speaker is used. • REAR (rear speakers) – YES: Normally select this. Specify the position and height to implement the Digital Cinema Surround modes. – NO: Select this if no rear speaker is used. continued 25GB xDISTANCE You can vary the distance of each speaker as follows. The default settings are underlined. • F. D. 5 m (17 ft) (front speakers distance) Front speaker distance can be set in 0.2 meters (1.0 foot) steps from 1.0 to 15.0 meters (3.0 to 50.0 feet). • C. D. 5 m (17 ft) (center speaker distance) Center speaker distance can be set in 0.2 meters (1.0 foot) steps from a distance equal to the front speaker distance to a distance 1.6 meters (5.0 feet) closer to your listening position. • R. D. 3.4 m (12 ft) (rear speakers distance) Rear speaker distance can be set in 0.2 meters (1.0 foot) steps from a distance equal to the front speaker distance to a distance 4.6 meters (15.0 feet) closer to your listening position. Notes • If each of the front or rear speakers are not placed an equal distance from your listening position, set the distance of the closest speaker. • In SPEAKER SETUP, the North American model’s OSD displays both metric and imperial measurements. The other model's displays metric measurements only. The manual shows both. Specifying the rear speaker position and height If you select anything other than “NO” in “REAR,” specify the position and height of the rear speakers. The default settings are underlined. Position diagram 90 20 45 AABB • R. P. BEHIND Select this if the rear speakers are located in the section B. • R. P. SIDE Select this if the rear speakers are located in the section A. 26GB Height diagram 60 30 CCDD Getting Started • R. H. LOW Select this if the rear speakers are located in section D. • R. H. HIGH Select this if the rear speakers are located in section C. These parameters are not available when “REAR” is set to “NO”. To specify the balance and level of the speakers 1 Press AMP MENU repeatedly to display 9 LEVEL on the front panel display. 2 Use X/x to select T.TONE and use C/c to set T.TONE to ON. You will hear the test tone from each speaker in sequence. 3 Sit in your listening position and select the item to be adjusted using X/x. • Items adjusted in 9 LEVEL – Balance of the front and rear speakers – Volume level of the center and rear speakers and subwoofer 4 Adjust the volume level so that the volume of the test tone from each speaker sounds the same using C/c. The adjusted value will appear on the front panel display. 5 Repeat Steps 3 and 4 to adjust other parameters in 9 LEVEL. If you do not operate the remote for a few seconds, the value disappears from the display and is stored in the system. 6 Use X/x to select T.TONE and use C/c to set T.TONE to OFF. xBALANCE You can vary the balance of each speaker as follows. The default settings are underlined. • F. ___I___ center (front speakers) Adjust the balance between the front left and right speakers (You can adjust from center, 6 steps left or right). • R. ___I___ center (rear speakers) Adjust the balance between the rear left and right speakers (You can adjust from center, 6 steps left or right). continued 27GB xLEVEL You can vary the level of each speaker as follows. The default settings are underlined. • C. LEVEL (0 dB) (center speaker level) Adjust the level of the center speaker (You can adjust from –6 dB to +6 dB in 1 dB steps.). • R. LEVEL (0 dB) (rear speakers level) Adjust the level of the rear speakers (You can adjust from –6 dB to +6 dB in 1 dB steps.). • S. W. LEV. (0 dB) (subwoofer level) Adjust the level of the subwoofer (You can adjust from –6 dB to +6 dB in 1 dB steps.). Notes • When you select an item, the sound cuts off for a moment. • Depending on the settings of other speakers, the subwoofer may output excessive sound. To adjust the volume of all the speakers at one time Use the VOLUME control. Other AMP MENU settings You can control the brightness of the front panel display, clear the preset stations and the station names, and set the speaker parameters back to the default setting. Press AMP MENU repeatedly to display 9 CUSTOMIZE. Use X/x to select the following items. xDIMMER You can change the brightness of the front panel display by two steps. xMEMO. CLR. • N (No): Skip back to previous menu. • Y (Yes): If you select Y by pressing ENTER, “Really? N” and “Really? Y” appears. If you select “Really? Y,” by pressing ENTER, “ALL CLEAR!” is displayed and all settings such as preset stations and station names will be cleared, and speaker parameters w...