Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Heimkino-Systeme - HT-SF2000 (2.1 mb)
Heimkino-Systeme - HT-SF2000 (3.06 mb)
Anleitung Zusammenfassung
Set this value using “SUR POS/ parameters in the SYSTEM menu (page 36). Tip When Auto Calibration starts: - Stand some distance from the speakers and the listening position to avoid measurement failure. This is because test signals are output from the speakers during measurement. - Avoid making noise to get a more accurate measurement. To cancel Auto Calibration The Auto Calibration function will be canceled when you do the following during the measurement process: - Press 1/1 or MUTING. - Press input buttons on the remote or INPUT SELECTOR on the receiver. - Change the volume level. - Press AUTO CAL again. Confirming/saving the measurement results 1 Confirm the measurement result. When the measurement ends, a beep sounds and the measurement result appears on the display. Measurement Display result Explanation When the SAVE Proceed to step measurement 2. process completes properly When the ERROR See “When measurement XXXX error codes process fails appear” (page 28). TV INPUT DMPORT SLEEP continued 27GB Getting Started 2 Press v/v repeatedly to select the item. Then, press (¿). Item Explanation RETRY Performs the Auto Calibration again. SAVE Saves the measurement results and exits the setting process. WARN CHK Displays warning concerning the measurement results. See “When you select “WARN CHK”” (page 28). PHASE Displays the phase of each speaker (in phase/out of phase). See “When you select “PHASE”” (page 29). DISTANCE Displays the measurement result for speaker distance. LEVEL Displays the measurement result for speaker level. EXIT Exits the setting process without saving the measurement results. 3 Save the measurement result. Select “SAVE” in step 2. The measurement results are saved. When error codes appear Try the remedies and perform the Auto Calibration again. Error code Cause and remedies ERROR 32 None of the speakers were detected. Make sure that the optimizer microphone is connected properly and perform the Auto Calibration again. If the optimizer microphone is connected properly but the error code appears, the optimizer microphone cable may be damaged or improperly connected. ERROR F 33 • None of the front speakers are connected or only one front speaker is connected. • The optimizer microphone is not connected. Error code Cause and remedies ERROR SR 33 Either the left or right surround speakers is not connected. ERROR SW 33 Sub woofer is not connected. Connect the sub woofer to the SUBWOOFER terminal. ERROR 33 Wrong speaker detection due to noise. Make sure the environment is quiet during Auto Calibration. To rectify the error 1 Record down the error code. 2 Press @, “RETRY Y” appears on the display. 3 Rectify the error. For details, see “When error codes appear” above. 4 Press @ to perform Auto Calibration again. When you select “WARN CHK” If a warning on the measurement result is present, detailed information is displayed. Press (f) to return to step 2 of “Confirming/saving the measurement results”. Warning code Explanation WARN 40 The Auto Calibration has completed. However, the noise level is high. You may be able to perform the Auto Calibration properly if you try it again, even though the measurement cannot be performed in all environments. Try to perform the Auto Calibration in a quiet environment. WARN 41 The sound input from the optimizer microphone is out of the acceptable range. It is louder than the loudest sound that can be measured. Try to perform the Auto Calibration when the environment is quiet enough to allow proper measurement. WARN 42 The volume of the receiver is out of the acceptable range. Try to perform the Auto Calibration when the environment is quiet enough to allow proper measurement. 28GB Warning code Explanation WARN 43 The distance and position of a sub woofer cannot be detected. This may be caused by noise. Try to perform the Auto Calibration in a quiet environment. NO WARN There is no warning information. When you select “PHASE” You can check the phase of each speaker (in phase/out of phase). Press v/v repeatedly to select a speaker, then press (f) to return to step 2 in “Confirming/saving the measurement results”. Display Explanation ■ IN The speaker is in phase. ■ OUT The speaker is out of phase. The “+” and “-” terminals of the speaker may be connected the other way around. * ■ ■ represent a speaker channel FL Front left FR Front right C Center SL Surround left SR Surround right SW Sub woofer Tip Depending on the position of the sub woofer, the measurement results for polarity may vary. However, there will be no problems even if you continue to use the receiver with that value. A. CAL menu parameters You can use the A. CAL menu to make settings for the Auto Calibration function to suit your preference. Select “8-A. CAL” in the amplifier menus. For details on adjusting the parameters, see “Navigating through menus” (page 34) and “Overview of the menus” (page 35). ■ AU...
Dieses Handbuch ist für folgende Modelle:Heimkino-Systeme - HT-SS2000 (1.09 mb)