Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Sony
Dateigröße: 911.88 kb
Dateiname: 4130029131.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Dieses Gerät hat auch andere Anweisungen:
Heimkino-Systeme - HT-SF100 (1.09 mb)
Heimkino-Systeme - HT-SF100 (1.78 mb)
Anleitung Zusammenfassung
Do not connect other microphones to this jack. Doing so may damage the receiver and the microphone. • During the calibration, the sound that comes out of the speakers is very loud. The volume of the sound cannot be adjusted. Pay attention to the presence of children or to the effect on your neighborhood. • Perform the Auto Calibration in a quiet environment to avoid the effect of noise and to get a more accurate measurement. • If there are any obstacles in the path between the optimizer microphone and the speakers, the calibration cannot be performed correctly. Remove any obstacles from the measurement area to avoid measurement error. Note If the muting function has been activated before you perform Auto Calibration, the muting function will be set to off automatically. continued 23GB Getting Started Example: HT-SS100 Optimizer Hüls dolî*^ microphone 1 Connect the supplied optimizer microphone to the AUTO CAL MIC jack. 2 Set up the optimizer microphone. Place the optimizer microphone at your listening position.You can also use a stool or tripod so that the optimizer microphone remains at the same height as your ears. Tip When you face the speaker towards the optimizer microphone, you will get a more accurate measurement. Performing Auto Calibration V/V/b, jiuikor ® AV 1/1 ^ OrO 0 © © ® SAT TV SA-CD/CD TUNER ^dvDU® Q . JU/UVL . TOP MENU MENU F1 F2 CEN CD CD CD DIGITAL ANALOG & AUDIO THEATRE •œ’CE’Œ) cd •CC'CO'Œ;) '(S) SOUND FIELD ‘CD‘CO "CID CD I/O switch Input buttons .o •return/exit 1 Press AMP MENU. 2 Press V/V repeatedly to select “A.CAL”. 3 Press @ or b to enter the menu. “START” appears on the display. 4 Press @ to start measurement. Measurement starts in 5 seconds. While the time is counting down, stand away from the measurement area to avoid measurement error. The measurement process will take approximately 30 seconds to complete. The table below shows the display when measurement starts. Measurement for Display Speaker existance TONE Speaker gain, distance, T.S.P. frequency response Subwoofer gain and distance WOOFER TV I/O 24eß Note If “CHK MIC” appears, you cannot perform the Auto Calibration. Connect the optimizer microphone, then perform the Auto Calibration again. Tips • When Auto Calibration starts: - Stand some distance from the speakers and the listening position to avoid measurement failure. This is because test signals are output from the speakers during measurement. - Avoid making noise to get a more accurate measurement. • The Auto Calibration function will be canceled when you do the following during the measurement process: - Press 1/1 or [$(. - Press input buttons on the remote or INPUT SELECTOR on the receiver. - Change the volume level. Confirming/saving the measurement results 1 Confirm the measurement result. When the measurement ends, a beep sounds and the measurement result appears on the display. Measurement Display result Explanation When the SAVE Proceed to step measurement 2. process completes properly When the ERROR See “When measurement XXXX error codes process fails appear” (page 25). 2 Press V/V repeatedly to select the item. Then, press @. Item Explanation SAVE Saves the measurement results and exits the setting process. WRN CHK Displays warning concerning the measurement results. See “When you select “WRN CHK”” (page 26). DIST Displays the measurement result for speaker distance. LEVEL Displays the measurement result for speaker level. EXIT Exits the setting process without saving the measurement results. 3 Note After “SAVE” is displayed for 50 seconds, the measurement result is saved automatically, without the need to save the procedure. Save the measurement result. Select “SAVE” in step 2. The measurement results are saved. When error codes appear Try the remedies and perform the Auto Calibration again. Error code Cause and remedies ERROR 32 • The sound input from the optimizer microphone is out of the acceptable range. • The optimizer microphone or subwoofer may be damaged. Contact your Sony dealer or local authorized Sony service facility. ERROR F 33 The front speakers are not connected. Check that the front speakers are connected properly. continued 25GB Getting Started Error code Cause and remedies ERROR SR33 Either the surround left or surround right speaker is not connected. Check that the surround speakers are connected properly. ERROR SW33 The subwoofer may be damaged. Contact your Sony dealer or local authorized Sony service facility. When you select “WRN CHK” If a warning on the measurement result is present, detailed information is displayed. Press © or B to return to step 2 of “Confirming/saving the measurement results”. Warning code Explanation WARN 40 The Auto Calibration has completed. However, the noise level is high. You may be able to perform the Auto Calibration properly if you try it again, even though the measurement cannot be...
Dieses Handbuch ist für folgende Modelle:Heimkino-Systeme - HT-SS100 (911.86 kb)
- ()
- ()