Stimmen - 5, Durchschnittliche Bewertung: 4 ( )

Hersteller: Anthem Audio Dateigröße: 3.07 mb Dateiname: Unterrichtssprache:

OPERATION .saûiiflusd 4.3 MANUALLY COPYING THE MAIN PATH TO ZONE2, ZONE3, OR RECORD When Main is copied to another Path, the Source selected in MAIN is directed to ZONE2, ZONE3, or RECORD from either analog or digital inputs. If a source component's audio is connected to the AVM 50 using digital connection only, then the Copy function is the only way to deliver the sound to another Path. Front Panel Press MAIN simultaneously with ZONE2, ZONE3, or REC. Use MAIN to select the Source. Remote Make sure the appropriate control mode is set, or REC Path is selected, then press COPY. 0 When MAIN is copied, the display for the other Paths reads "-MAIN-> ZONE2" (or ZONE3 or REC), along with the information normally displayed. Copy can also be set permanently - see section 3.5. Down-Mixing to 2-Channel Stereo: The Center, Surround, and Rear channels can be mixed into the Left and Right Channels for the ZONE2, ZONE3, TAPE, and VCR outputs. This can be done by the DVD player or the AVM 50: • AVM 50 Down-mix: If the digital audio output from your DVD player is connected to the AVM 50, the AVM 50 down-mixes 5.1 channels into 2.0 whenever you copy MAIN to another Path. This applies whether the input is, Dolby Digital, DTS, or 6-Ch input. • DVD Player Down-mix: If the Left/Right analog outputs from your DVD player are connected to the AVM 50's Analog Audio-In, the Dolby Digital down-mix done by your DVD player can be used for ZONE2, ZONE3, TAPE, and VCR outputs, without having to copy MAIN. Note that DVD players do not normally provide a down-mix for DTS material. 4.4 SOURCE SELECTION After making sure that you are in the appropriate Path (Front Panel) or appropriate control mode is set (Remote Control), select a Source. 6-Channel Analog Audio Input: The 6-Ch audio can be routed to ZONE2, ZONE3, and RECORD outputs as long as Copy mode, which creates the stereo down-mix, is used (see section 4.3). Source Seek (Remote Control Only): The SOURCE SEEK M ►► keys detect the previous/next active Source, while the ► key advances one Source at a time. To increase seeking speed, set all unused HDMI and Component video inputs to 'None' (see section 3.5). 45 4. OPERATION 4.4.1 FM^AM TUNER The AVM 50 has a built-in FM • AM tuner, which is common to all Paths. The station that is selected in either MAIN, ZONE2, ZONE3, or RECORD is shared with all other Paths. Manual Tuning: After selecting the desired band by pressing FM • AM, use the buttons (Remote Control) or press TUNE and rotate the Master Control Knob (Front Panel). Automatic Tuning: To find the next station, press 4 SEEK or SEEK ► . To scan and listen to all available stations for a few seconds, press and hold 4 SEEK or SEEK ► for about a second. The '4 Sk' or ' Sk ►' indicator on the display will change to '4 Prv' or ' Nxt ► '. To stop scanning, press one of the 4 SEEK ► buttons to return to Seek mode, or press TUNE to tune manually (Front Panel only). Press TUNE a second time to restore the regular functions and display (the TUNE function does not time out). Direct Tuning (Remote Control Only): A station's frequency can be entered as a four-digit number. For example, to tune into 98.3 FM, press and hold SELECT until the display shows "0.0" in the lower left corner, then press 0,9,8,3. Presets: 18 FM and 6 AM stations can be stored. The presets are divided into four banks of six. By repeatedly pressing FM^AM, the display will show that you are cycling through 'FM1', 'FM2', 'FM3', 'AM'. Once you have selected the desired bank, you can store the currently tuned radio station by pressing and holding one of the six preset keys (1 through 6) for about a second. You can even do this while scanning for stations. The lower line of the display briefly flashes once the station is stored. To skip a preset, set it to 87.5 FM or 530 AM. o o o o o o To recall a preset, select the bank that it is in, then press the respective preset key. From the Remote Control, you can also use the CH+ and CH- keys to run through all FM or AM presets. ST / HiB / M (Front Panel Only): If FM reception is weak, switching a station out of stereo can reduce or eliminate unwanted noise. Press ST / HiB / M repeatedly to cycle through Stereo, Hi-Blend, or Mono. Hi-Blend offers an alternative to Mono, offering decreased noise without the complete loss of stereo - it decreases hiss and noise by reducing some stereo separation only at higher frequencies. The setting is memorized individually for each preset. 4.4.2 SIMULCAST Simulcast allows you to select one video Source and a different audio Source. For example, you could view a sports event on TV while listening to your favorite FM • AM station. Simulcast is available for all Paths. Press and hold the desired video Source button for 2 seconds. The display shows "SIMULCAST" and the video Source in the top line, and the audio Source in the bottom line - while this is on the display, press another Source button to select an a...

Herunterladen

Geben Sie zwei Ziffern: