Stimmen - 4, Durchschnittliche Bewertung: 4.8 ( )

Hersteller: Atlantic Technology Dateigröße: 469.38 kb Dateiname: Unterrichtssprache:

But their presence or absence is never an assurance that there is not something within the wall cavity. 5 System 10 InWall Speakers There must be a minimum depth behind the wall face of 3 5/8 (92 mm). Be sure to keep the edges of the cutout at least 1 inch (25 mm) away from any stud or obstruction. The speaker assembly itself (the part with the drivers mounted in it, the trimming bezel, etc.) is designed to mount to the Installation Bracket after it has been installed within the wall. Step 1. Tilt one corner of the Installation Bracket into the opening and continue to slide it fully into the wall cavity until it fits completely into the cutout. Be sure to position the side extensions so they press against the inside of the wall. Step 2. Carefully insert the tabs into the Installation Bracket as shown in Fig. 1.They are a tight fit and are best installed by “clamping” them with your hand as shown. Alternately, there are predrilled holes in the side flanges of the Installation Bracket that may be used to hold the assembly to the wall board with #6 self-threading screws, instead of using the tabs.These screws will be hidden by the speaker’s bezel when it is mounted. Step 3. After the Installation Bracket is fixed in place note that there are holes near the center of the long sides that can be used to secure feed wiring using the included nylon wire ties. Step 4. Strip about °” of insulation from the connecting wires. Insert them into the appropriate push terminal on the rear of the speaker assembly, being careful to observe polarity (positive to the red terminal, negative to the black terminal).Typically, with standard “zip” cord wiring the marked wire is used for the positive lead. Markings typically consist of a thread within one conductor, printing on the wire’s insulation, a ridge or ridges on the insulation, or a flat side to the insulation. Step 5. Carefully position the speaker assembly into the wall cutout and Installation Bracket. Check that it’s level and then attach the speaker to the Installation Bracket with the included 3 inch #6 self-tapping screws. (If the assembly is not level, you can oversize the wall opening very slightly to allow straightening the bracket and speaker.) Step 6.Tighten the mounting screws, which in turn will cause the bezel and the Installation Bracket to clamp the wall board between them.Be very careful not to overtighten the screws as this can make the grille difficult or impossible to install.The outer trim bezel has been specially designed to flex and conform to the wallboard.This makes for a good seal and eliminates rattles but it also means that the speaker mounting screws should be snug, but not overly tight. Should you have any questions or problems please feel free to contact us at 781-762-6300 or through our web site, Customer Service@atlantictechnology.com. Fig 1 Installing the Mounting Bracket Fig. 2 Installing the clamping tabs 6 System 10 InWall Speakers Speaker and Cutout Dimensions System 10 LCR 8 13/16 inches OutsideDimensions aaaaaaaaaaaaaaaaaaaaaaaaaaa 7 inches 15 13/16 inches aaaaaaaaaaaaaa Cutout Dimensions17 1/4 inches System 10 SR Surround 15 5/8 inches aaaaaaaaaaaaaaaaaaaaaaaaaaaaa 11 inches 14 3/8 inches aaaaaaaaaaaaaaaaaaCutout Dimensions OutsideDimensions 12 1/16 inches 7 System 10 InWall Speakers Toe nail or screw to hold firebock in position until sealant dries. Seal edges with caulking Mounting Hole Outline Speaker Frame Outline Proportions illustrated are for 16" on-center 2" X 4" stud installation. See table below for proper dimensions. See table for proper dimension System 10 LCR InWall Enclosure Recommendations Please use this information to construct an in-wall enclosure if you so desire. Doing so will generally improve the performance and increase the power handling of the system. We have not included information for the System 10 SR since one of its woofers is self-enclosed and the other will not generate anywhere near the bass energy the LCR system will. Be sure to line the cavity with weatherproof insulation, being careful to avoid letting the insulation touch the backs of the woofer cones. It’s also important to seal the joints of the enclosure with a high quality non-shrinking caulk. Be careful to keep the wires from touching the chassis of the drivers or baffle in such a manner that the wire might vibrate and buzz. You may use nylon wire ties to keep the wires properly positioned. Such ties are available that are designed to screw directly to studs making them ideal for this purpose. As always, take care to wire the speakers properly, with the positive lead (normally marked with a red terminal or a “+” sign) from the amplifier connected to the positive terminal on the speakers and the negative (marked with a black terminal or a “-” sign) connected to its respective terminals. 2 x 4 Construction 1ft3 1.25ft3 16" O.C.Studs 34" 42.5" 24" O.C. Studs 22" 27.5" 2 x 6 Construction 1ft3 1.25ft3 16" O.C.Studs ...

Herunterladen

Geben Sie zwei Ziffern: