Stimmen - 5, Durchschnittliche Bewertung: 4.2 ( )

Hersteller: Culligan Dateigröße: 2.6 mb Dateiname: Unterrichtssprache:

For the dealer nearest you, call 1-800-BUY-MOEN. Use only MicroTech filter cartridges with the PureTouch® Filtering Faucet System. Do not remove the filter until it is to be replaced. 1. Remove pullout spout (19) from receptor (15) and tie a dish towel around the hose to keep it from slipping back into the spout receptor. 2. Disconnect the quarter turn connector (18) from pullout spout by turning it counterclockwise one quarter turn. Quarter turn connector will remain on the hose. 3. Remove the filter cover by lifting it up and away from the pullout spout assembly. Remove the filter by lifting it up and away from the pullout spout assembly. NOTE: Excess water may dribble from cartridge and valving. 4. Using soft towel or cloth, wipe excess water from wand appliance. 5 Insert the new filter by aligning the two outlet tubes on the filter with the two inlet ports of the spout body and gently pressing in and down. Upon successful installation of the filter cartridge, the pullout spout will beep three times and the filter life indicator will reset automatically. 6. Reinstall the filter cover by positioning the alignment tab with the corresponding notch in the main pullout spout body and gently pushing in and down. 7. Reattach the filtering pullout spout to the hose by aligning the dots on the quarter turn connector (18) and the pullout spout (19). Push the quarter turn connector onto the pullout spout assembly and turn it clockwise locking it in place. 8. Allow water to run through the new filter for 5 minutes to flush out any loose carbon particles. After these small black particles are washed out the filter is ready to be used. ALIGN DOTS (7) (6) (3) (2) FILTER COVER ALIGN DOTS (7) (6) (3) (2) FILTER COVER TROUBLESHOOTING PROBLEM: Water drips from hose and quarter turn connection. SOLUTION: Make sure screen washer (17) is in place. PROBLEM: Slow or uneven water flow in unfiltered modes. SOLUTION: The screen washer has become clogged. Ensure faucet handle is in a closed position. Remove pullout spout from receptor and tie a rag around the hose to keep it from slipping back into the spout receptor. Disconnect the quarter turn connector (18) from hose connection (16). Remove screen washer (17) from hose connection. Clean screen washer with a toothbrush and rinse. PROBLEM: Reversed Hot & Cold positions. SOLUTION: HELPFUL HINTS: IT IS NOT NECESSARY TO SHUT OFF WATER. SUPPLIES. HANDLE SCREW REQUIRES A 7/64” HEX KEY WRENCH. 1. Remove plug button (3) from the handle by prying the button upwards from the bottom center. If a tool is required, use something which will not scratch the handle. Remove set screw (2), handle body (1), dome (4), cartridge screw (5), handle adapter (6) and handle connector (7). 2. Turn cartridge stem around so that the notch is turned one half turn or 180°. 3. Reinstall as follows: Be sure retainer clip (13) is present on cartridge stem and raised edge of pivot stop (10) faces front. Note orientation of handle adapter & connector assembly (6 & 7) in the exploded view. Completely turn cartridge screw (5) to prevent unwanted closure of faucet. Thread on dome clockwise until hand tight. Reinstall handle body (1), set screw (2) and plug button (3). PROBLEM: Pullout hose does not move freely. SOLUTION: Gently bend supply tubes away from the hose. DO NOT KINK SUPPLY TUBES. PROBLEM: Slow or uneven water flow in filtered mode. SOLUTION: Filter outlet nut (21) may be clogged. 1). Remove filter outlet nut, flush out carbon particles. 2). Filter cartridge may be clogged with captured contaminants. Replace filter cartridge. If problem persists call Moen Helpline at 1-800-BUY-MOEN PROBLEM: Water drains from sides of pullout spout when water is on. SOLUTION: Filter may be cracked. Replace filter. PROBLEM: Electronic display doesn’t function. SOLUTION: Replace battery. INS115D HELPLINE: 1-800-BUY-MOEN 14 . . TURN STEM 1/2 TURN NOTCHED FLAT ON STEM 10 . . PureTouch Filtering Faucet System Warranty Definitions: “Faucet” - That part of the PureTouch Filtering Faucet System that includes the handle, spout receptor, 1225 cartridge, escutcheon, hose and mounting hardware (numbers 1-17 & 23-40 & 42 in parts description (page 4)). “Wand Appliance” - The hand held part of the PureTouch Filtering Faucet System that includes the quarter turn connector and pull-out spout (numbers 18-22 in parts description (page 4)). “Filter” - That part of the PureTouch Filtering Faucet System that is to be replaced once 200 gallons of water have run through the system (number 41 in part description (page 4)). Moen products have been manufactured under the highest standards of quality and workmanship. Moen warrants to the original consumer purchaser that for as long as the original consumer purchaser occupies the location of original product installation (the “Warranty Period”), that the Faucet (see definition for “Faucet” above) will be leak and drip-free during normal use and all parts and finishes of the Faucet will be free from defe...

Herunterladen

Geben Sie zwei Ziffern: