Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
In this case, proceed from step 2. NxPLAY/STOP MENU ./> 1 Press MENU to enter the menu mode. 2 Display the clock setting display. 1 Press .once to 2 Press NxPLAY/ display “SET STOP. DATE”. The year digits will flash. 3 Set the date. 1 Press . or > 2 Press NxPLAY/ 3 Set the month and to select the STOP. day in sequence, digits of the year. The month digits then press will flash. NxPLAY/STOP. The hour digits will flash. 10GB 4 Set the time. 1 Press . or > 2 Press NxPLAY/ 3 Set the minute. to select the STOP. digits of the hour. The minute digits will flash. 5 Press NxPLAY/STOP at the time signal. The display will return to “SET DATE”. 6 Press MENU to exit the menu mode. 1 Tip This unit does not have a power on/off switch. The display is shown at all times. Getting Started 11GB BBasic Operations Recording Messages You can record up to 99 messages in each of three folders (A, B, or C). Since a newly recorded message is automatically added behind the last recorded message, you can start recording quickly without searching for the end of the last recording. e.g. Message 1 Message 2 Blank spaceNewly recorded message Note Before making a long recording, be sure to insert new batteries and check the battery indicator (page 9). 1 Select the folder . Current folder Press FOLDER repeatedly to display the folder (A, B or C) in which you wish to record messages. Start recording. 2 1 Press zREC/STOP. 2 Speak to the built-in microphone. Remaining memory indicator OPR indicator (lights in red during recording.) Current You do not need to keep message pressing zREC/STOP number while recording. Counter display* 12GB * The display selected with the DISPLAY button (page 39) appears. Stop recording. Press zREC/STOP again. The unit stops at the beginning of the current recording. xSTOP 3 Stop recording. Press zREC/STOP again. The unit stops at the beginning of the current recording. xSTOP 3 If you do not change the folder after you stop recording, the next time you record you will record in the same folder. To stop recording You can also stop recording by pressing xSTOP instead of zREC/STOP. To pause recording To Do this pause recording* Press XPAUSE. During recording pause, the OPR indicator flashes in red and “PAUSE” flashes in the display window. release pause and Press XPAUSE or zREC/STOP. resume recording Recording resumes from that point. (To stop recording after pausing recording, press xSTOP.) * 15 minutes after you pause recording, recording pause is automatically released and the unit goes into the stop mode. Continued Basic Operations 13GB Recording Messages (continued) To select the microphone sensitivity You can select the microphone sensitivity by switching the MIC SENS selector on the rear of the unit. H (high): To record at a meeting or in a quiet and/or spacious place. L (low): To record for dictation or in a noisy place. To monitor the recording Connect the supplied earphone to the EAR jack. You can adjust the volume with the VOL control, but the recording level is fixed. Note If you turn up the volume excessively or place the earphone near the microphone while monitoring recording, the microphone may pick up the sound from the earphone, causing acoustic feedback (howling sound). Maximum recording time You can record for up to 63 minutes in SP (standard play) mode and 168 minutes in LP (long play) mode. If you record messages in a mixture of SP and LP modes, the recordable time varies from 63 to 168 minutes. The unit is factory-set to SP mode. To change the recording mode, see page 41. You can check the remaining amount of recording time by selecting the remaining recording time display mode. See page 39. Remaining memory indication During recording, the remaining memory indicator decreases one by one. flashing When the remaining time of recording reaches 5 minutes, the last one of the indication flashes. When the remaining time of recording reaches 1 minute, the selected display mode (page 39) and “REMAIN” will flash one after the other in the display window. When the memory is full, recording automatically stops and “FULL” will flash in the display window with an alarm sound. To continue recording, first erase some of the messages (page 20). 14GB Various Ways of Recording Starting recording automatically in response to the sound — Advanced VOR function When VOR (voice operated recording) selector on the rear is set to ON, recording starts when the recorder detects sound and stops when no sound is heard. Note VOR function is affected by the sound around you. Set the MIC SENS selector to either H or L (see page 14). If recording is not satisfactory after you have changed the microphone sensitivity, or for important recording, set the VOR selector to OFF. Recording with an external microphone or from other equipment Connect a plug-in-power type microphone or other equipment to the MIC (PLUG IN POWER) jack. When you connect an external microphone, the built-in microphone is automatically cut off. When a plug-in-po...