Stimmen - 4, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Kenwood Dateigröße: 4.02 mb Dateiname: Unterrichtssprache:

Dieses Gerät hat auch andere Anweisungen:

Car-Receiver - KRC-37 (1.46 mb)

Car-Receiver - KRC-37 (4.41 mb)

A–4 1 Battery 2 Ignition (ACC) A–5 Power Control A–7 1 Ignition (ACC) 2 Battery A–8 Earth (Ground) Connection B–1 Rear Right (+) B–2 Rear Right (–) B–3 Front Right (+) B–4 Front Right (–) B–5 Front Left (+) B–6 Front Left (–) B–7 Rear Left (+) B–8 Rear Left (–) *Plug setting: — 25 — 25— 25 — —— 10 • If both the A-7 pin and power supply, use Plug setting 2. • If the A-7 pin is connected and the A-4 pin Wiring harness 1). English Connecting Wires to Terminals ¦ Power Control Terminal Connections The output of the Power Control terminal is switched along with the power on/off switching of the unit. This terminal can be connected to the P.CON (REMOTE) terminal of the amplifier, or used as the power supply of the special antenna adapter for Volkswagen cars. (MAX. 310 mA) Power Control terminal (Flat terminal) Power Amplifier Antenna Cord (ISO) Antenna Conversion Adaptor (ISO–JASO) (Accessory3) Power control wire Special antenna adapter (For Volkswagen car) (Commercially available) Installation ¦ Installation Firewall or metal support Make sure that the unit is installed securely in place. If the unit unstable, it may malfunction (eg, the sound may skip). Metal mounting strap (commercially available) Self-tapping screw (commercially available) Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. — 26 — 26— 26 — —— ¦ Removing the hard rubber frame 1 Engage the catch pins on the removal tool and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure. 2 When the lower level is removed, remove the upper two locations. The frame can be removed from the CatchLock Accessory2 Removal tool ¦ Removing the Unit 1 Refer to the section "Removing the hard rubber frame" and then remove the hard rubber frame. 2 Remove the screw (M4.8) on the back panel. 3 Insert the two removal tools deeply into the slots on each side, as shown. Accessory2 Removal tool Screw (M4X8) (commercially available) 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Be careful to avoid injury from the catch pins 5 Pull the unit all the way out with your hands, being careful not to drop it. — 27 — 27— 27 — —— English Troubleshooting Guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The power does not turn ON. . The fuse has blown. . After checking for short circuits in the wires, replace the fuse with one with the same rating. . No ACC position on vehicle ignition. . Connect the same wire to the ignition as the battery wire. ? If you have selected Standby mode, the power will go OFF automatically. . The Power OFF Timer function has been activated. . If you do not want the power to go OFF automatically, cancel the Power OFF Timer function. ? Nothing happens when the buttons are pressed. . The computer chip in the unit is not functioning normally. . Press the reset button on the unit (page 4). ? There’s a source you can’t switch. . There’s no tape inserted. . Set the media you want to listen to. If there’s no media in this unit, you can't switch to each source. . The Disc changer isn’t connected. . Connect the Disc changer. If the Disc changer isn’t connected to it's input terminal, You can't switch to an external disc source. ? The memory is erased when the ignition . The battery wire has not been connected . Connect the wire correctly, referring to the section on . . The ignition and battery wire . Connect the wire correctly, referring to the section . ? The TEL mute function turns ON even though the TEL mute wire is not connected. . The TEL mute wire is touching a metal part of the car. . Pull the TEL mute wire away from the metal part of the car. ? No sound can be heard, or the volume is low. . The fader or balance settings are set all the way to one side. . Center the fader and balance settings. . The input/output wires or wiring harness are connected incorrectly. . Reconnect the input/output wires or the wiring harness correctly. See the section on "Connecting Wires to Terminals". . The cassette tape is bad. . Try playing another cassette tape. If works fine, the first tape was bad. ? The sound quality is poor or distorted. . One of the speaker wires is being pinched by a screw in the car. . Check the speaker wiring. . The tape head is dirty. . Clean the tape head. . The speakers are not wired correctly. . Reconnect the speaker wires so that each output terminal connected to a different speaker. ? The Touch Sensor Tone doesn’t sound. . The preout ja...

Herunterladen

Geben Sie zwei Ziffern: