Stimmen - 5, Durchschnittliche Bewertung: 4.2 ( )

Hersteller: Graco Dateigröße: 2.56 mb Dateiname: Unterrichtssprache:

See “3.3 Removing and Attaching Base” and “3.4 Adjusting Handle”, p. 13. 2. Place child in infant restraint as shown . 3. Determine which pair of harness slots are even with or just below your child’s shoulders . DO NOT use upper harness slots if they are above your child’s shoulders. They will not hold a small child securely in a sudden stop or crash. 4. If the harness straps must be adjusted: remove child from infant restraint and follow directions for your type of harness system: 6.1.1 3-Point Harness - p. 28 Use harness slots even with or just below 6.1.2 5-Point Harness - p. 29 child’s shoulders 27 6.1.1 3-Point Harness 1. From back, push harness anchor buckle back through harness slot. If necessary, from front, use harness strap to pull buckle from slot . Harness tightener 2. Reinsert harness anchor buckle in the appropriate slot . 3. From back, remove harness strap from harness tightener. If necessary, from front, use harness strap to pull strap from slot. 4. Reinsert strap in the appropriate slot. Thread strap through tightener exactly as shown . 5. SAFETY CHECK: a) CHECK that straps are not twisted; b) CHECK that straps are secure: pull on harness straps from front. c) CHECK that harness anchor buckle is snapped flat against back as shown . Harness anchor buckle 28 6.1.2 5-Point Harness 1. Depress the harness adjustment button under the seat flap . Pull the shoulder straps out to loosen the harness. 2. Behind seat, remove the ends of the two shoulder straps from the metal junction plate . 3. From front, pull straps through the harness slots and then reinsert them through the appropriate slots. 4. Behind seat, push both shoulder straps UNDER owner’s manual pocket and out the bottom. 5. Reassemble the strap ends onto the metal junction plate . Follow the appropriate instructions for a smaller or larger baby on the following page. Harness adjustment button 6. SAFETY CHECK: After the harness has been completely reinstalled, a) CHECK that harness straps are not twisted in front or back. b) CHECK that straps are secure by pulling on them. 29 FOR SMALLER BABY: Use the lower harness slots (if they are even with or just below your child’s shoulders) and the upper strap loops . The ends of the straps must hang in front of the metal plate as shown in , not as shown in . CHECK that the loops are completely within junction plate slots . CHECK that straps are secure by pulling on them. FOR LARGER BABY: Use upper harness slots and the end strap loops . CHECK that the loops are completely within junction plate slots . CHECK that straps are secure by pulling on them. 30 6.2 Securing Child in Infant Restraint Failure to properly secure your child in the infant restraint/carrier increases the risk of serious injury or death from suffocation or falls, or in the event of a sudden stop or crash. Even when used only as a carrier, make sure the harness straps are properly secured. 1. Move infant restraint handle to sitting position (see page 13). 2. Open harness clip by squeezing both sides and unbuckle as shown . 3. Place your child in the infant restraint as shown in , not . Pull the harness straps down over your child. 4. Follow directions for your harness: 6.2.1 3-Point Harness: p. 32 6.2.2 5-Point Harness: p. 33 OR 31 6.2.1 3-Point Harness 5. Buckle harness to the latch between child’s legs. Make sure that you hear a “click.” DO NOT use the infant restraint if the harness does not latch in place. Call Graco at 1-888-224-6549. 6. From the back, pull strap through harness tightener to tighten the straps as shown . CHECK that both straps are flat and tight on child’s shoulders. 7. Snap harness clip pieces together . Position harness clip in middle of chest, level with armpits and away from the neck . 8. SAFETY CHECK: a) CHECK that harness straps are not twisted. b) CHECK that the harness is snug. A snug strap should not allow any slack. It lies in a relatively straight line without sagging. It does not press on the child’s flesh or push the child’s body into an unnatural position . 32 6.2.2 5-Point Harness 5. Insert the two buckle tongues into the harness buckle on the crotch strap. Make sure that you hear each tongue click into the buckle. DO NOT use the infant restraint if the harness does not latch in place. Call Graco at 1-888-224-6549. 6. Snap harness clip pieces together . 7. Pull on harness adjustment strap to tighten straps as shown . CHECK that both straps are flat and tight on shoulders. 8. level with armpits and away from the neck . 9. SAFETY CHECK: a) CHECK that harness straps are not twisted. lies in a relatively straight line without flesh or push the child’s body into an unnatural position . Position harness clip in middle of chest, b) CHECK that the harness is snug. A snug strap should not allow any slack. It sagging. It does not press on the child’s 33 6.3 Installing the Infant Restraint/Base Using Vehicle Belt You must carefully follow the instructions provided by your vehicle manufactu...

Herunterladen

Geben Sie zwei Ziffern: