Login:
Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Anleitung InStep, modell 20K

Hersteller: InStep
Dateigröße: 591.3 kb
Dateiname:
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


Lock both plastic latches onto the lower frame, insert locking pin into hole in latch and frame, lock the pin in place by slipping the wire loop over the end of the lock pin. On Double Models repeat for other side. (Figures A1, A2, A3, A4 and A5). A1 A2 A3 A4 A5 Back Rest Handle Rear Frame Latches Side Latch Locking Pin Locking Pin Open Locking Pin Closed Front Fork 2 Step 2. Rear Wheel Assembly Turn stroller onto its side. Grasp rear wheel in one hand, slide wheel’s axle into hole in rear of frame. Push up on the axle release lever so that the wheel is fully inserted (Figure B). Check to see that the wheel is properly inserted by pulling on the wheel firmly, the wheel should not come off if fully inserted/locked. Repeat for other side. To release wheel push up on axle release lever and pull off wheel. Step 3. Front Wheel Assembly Turn stroller upright onto its rear wheels and then tip stroller back so that the handlebar is down on the ground and the front fork is up. The front brake Quick B Rear Axle Axle Release Button D2 Release le should be in the open position (Figure C). Attach the front wheel b Release (Q/R) le allo With wheel’ the cone n le place until the Q/R le (Figure D2). loc The interior jam n y installed and do not need adjustment. Close the front caliper brake by lowering the Q/R lever (See Figure C). Spin the front wheel to make sure the brake pads do not rub and are properly aligned to the rim. If brake pad alignment is off, loosen brake pad nut with an adjustable wrench, align brake pad and retighten nut while holding brake pad in place. WARNING: Always be sure to reengage the brake by rotating the Q/R lever forward (toward the front wheel) before using the stroller. C D1 Brake Pad Cable Cap Cable Adjustment Nut Locknut Brake Cable Cable Adjusting Sleeve Q/R Brake Lever Open Position Closed Position 3 IMPORTANT F E Pull Seat Back Forward for folding stroller The alignment of the front wheel determines if the stroller will roll straight, or veer to the right or left during use. In the event you notice the stroller veering to one direction, loosen front axle Q/R lever, point the front wheel in the opposite direction the stroller is veering, and retighten the Q/R lever. If you need help making this adjustment, please call our Customer Service department for assistance. Note: If it is necessary to remove the front wheel, you will find it easier to open the brake Q/R lever by taking pressure off the cable. This is achieved by squeezing the brake pads with one hand while rotating the lever backward (toward the seat) (Figure E). WARNING: Always be sure to reengage the brake by rotating the Q/R lever forward (toward the front wheel) before using the stroller. Step 4. Front Fender Assembly Insert the #8 – 11/2" screws into the holes located on the front support between the front forks. Align the 2 holes on the bottom side of the fender with the screws and tighten with a Phillips screwdriver. Note: The Double Models have 4 screws. Step 5. Canopy Positioning The canopy has adjustable positions. Pull the canopy down to the desired position. Step 6. Attaching Wrist Strap Place strap on top of handle bar. The wrist strap has different sized loops. The large loop will go on your wrist, the small loop will be on handlebar. Slide end with large loop through the small loop, then grasp the end with the large loop and pull strap to tighten on handlebar. WARNING: Whenever child is in stroller always use the wrist strap. Before you remove the wrist strap from your wrist make sure you first ...

Dieses Handbuch ist für folgende Modelle:
Kinderwagen - 10K (591.3 kb)
Kinderwagen - 5K (591.3 kb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien