Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: InStep Dateigröße: 547.18 kb Dateiname: Unterrichtssprache:

Service will be quicker if you have your model number (found on the product and box) along with this instruction sheet ready when calling. If you have any questions concerning the safe use of this product, please contact us immediately. {Figure 1.a} canopy handle locking pin frame parking brake rear wheel foot plate 5K_double_Platform.indd 2 9/26/05 3:50:14 PM Parts List: Description Qty. Frame assembly with seat, canopy, and wrist strap 1 Front Wheel 1 Parent Console (not on all models) 1 Under-seat Basket (not on all models) 1 Rear Wheels 2 Front Fender 1 #8 – 11.2" Phillips head screws 4 Tools Required: Phillips screw driver, adjustable wrench. Stroller Assembly Instructions Unfold Stroller: Remove from carton and remove any packaging materials that may be holding the frame in closed position. Grasp frame handle and open. Lock both plastic latches, on sides, onto the lower frame, insert locking pin into hole in latch and frame, lock the pin in place by slipping the wire loop over the end of the lock pin. {see Figure 1.A} Rear Wheel Assembly Grasp rear wheel in one hand, slide wheel’s axle into hole in rear of frame. Push up on the axle release lever so that the wheel is fully inserted. Pull the wheel firmly, the wheel should not come off if fully inserted/locked. Repeat for other side. To release wheel push up on axle release lever and pull off wheel. Front Wheel Assembly Tip stroller back so that the handlebar is down on the ground and the front fork is up. Attach the front wheel by loosening the wheel’s Quick Release (Q/R) lever on the front wheel far enough to allow the axle to slide into the front fork. With wheel’s Q/R lever in open position, hand tighten the cone nut until almost tight, then flip wheel’s Q/R lever backward to the closed position to lock wheel in place. Note this step may require minor adjustment until the Q/R lever flips back m pressure. Pull outward on wheel to ensure it is locked in place. Caution: The interior jam nuts are factory installed and do not need adjustment. Close the front caliper brake by lowering the Q/R lever. Spin the front wheel to make sure the brake pads do not rub and are properly aligned to the rim. If brake pad alignment is off, loosen brake pad nut with an adjustable wrench, align brake pad and retighten nut while holding brake pad in place. Caution: Always be sure to reengage the brake by rotating the Q/R lever forward (toward the front wheel) before using the stroller. IMPORTANT If you notice that the stroller steers to one direction you may need to adjust the front wheel to align it. To do so loosen the front axle Q/R lever, points the front wheel in the opposite direction the stroller is veering, and retighten the Q/R lever. If you need help making this adjustment, please call our Customer Service department for assistance. axle release lever Rear Wheel Assembly - {Figure 1.b} quick-releaselever (open position) Front Wheel Assembly Operating Instructions Run Around™ & Run Around™ LTD 11-KS207, 11-KS286, 11-KS287...page 2 axle release lever Rear Wheel Assembly - {Figure 1.b} quick-releaselever (open position) Front Wheel Assembly Operating Instructions Run Around™ & Run Around™ LTD 11-KS207, 11-KS286, 11-KS287...page 2 5K_double_Platform.indd 3 9/26/05 3:50:16 PM To recline seat To fully recline, unhook buckle on back of the seat.To adjust the recline position; adjust the slide on the strap to the desired length. WARNING: Child may slip into leg openings and strangle. Never use in a reclined carriage position unless T-shield and shoulder strap have been readjusted to the new seat position. Storage and folding WARNING: Always remove child from stroller before folding Pull the back of the seats forward. It will be easier to fold if the seats are not in the recline position. Remove locking pins from side latches on the stroller frame (Double Models have 2 locking pins). Release the two latches from the frame. The stroller may automatically begin to fold, the front wheel will fold under frame and the handle will fold backwards. Storage and folding Front Fender Assembly Insert the #8 – 1.5" screws into the holes located on the front support above the wheel. Align the holes on the bottom side of the fender with the screws and tighten with a Phillips screwdriver. Parent Console (not included on KS207) The parent console will attach to the handle by snapping it in place on the handle and above the canopy. Tether Attachment The wrist strap has different sized loops. The large loop will go on your wrist; the small loop will be on handlebar. Slide end with large loop through the small loop, then grasp the end with the large loop and pull strap to ...

Herunterladen

Geben Sie zwei Ziffern: