Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
In the West, results may take one to two years in areas of low rainfall. 9 SPRAY EQUIPMENT When applied as a liquid spray using water as the carrier, DuPont™ VELPAR® DF may be applied by ground equipment or by air (helicopter only). MIXING INSTRUCTIONS For ground application, use enough water for thorough coverage, usually a minimum of 25 gal per acre. For aerial applications, use at least 5 gal of water per acre. SITE PREPARATION - TANK MIXTURES VELPAR® DF PLUS “Tordon 101” MIXTURE For improved, broad-spectrum brush control, tank mix VELPAR® DF with “Tordon 101” Mixture. Only the following trees may be planted on sites with this combination: Austrian pine Loblolly pine Longleaf pine Ponderosa pine Red pine Scotch pine Shortleaf pine Slash pine Virginia pine APPLICATION TIMING Apply VELPAR® DF plus “Tordon 101” Mixture from late spring to early summer after the trees have reached full leaf, but before leaf tissue hardens. In the states of Maine, Michigan, Minnesota, New Hampshire, New York, Vermont, and Wisconsin, apply this tank mixture after bud break. WOODY PLANTS CONTROLLED - USE RATES Predominant VELPAR® DF “Tordon 101” M Species (Lb/Acre) (Qt/Acre) Blackberry, Elm, 4 - 6 2/3 4 Oak (Prunus spp.), Sweetgum Blackgum, Dogwood, 2 2/3 - 6 2/3 6-8 Pine, Red maple, Sassafras, Sourwood Refer to the USE RATES table in the FORESTRY SITE PREPARATION section of this label for recommended rates based on soils. SPRAY EQUIPMENT VELPAR® DF plus “Tordon 101” Mixture may be applied by ground equipment or by air (helicopter only). MIXING INSTRUCTIONS For ground application, use enough water for thorough coverage, usually a minimum of 25 gal per acre. For aerial applications, use at least 5 gal of water per acre. For best results, full foliar coverage is required. USE PRECAUTIONS - VELPAR® DF + “Tordon 101” Mixture •To avoid injury, do not plant pine before the following intervals following application with “Tordon 101” Mixture: –Southern states - 6 months –Lake states - 9 months –Northeastern states - 9 months • Burning treated sites after initial contact (browning) effect on foliage may result in poor control. Burn the vegetation only after brush has completely defoliated at least once, allowing sufficient root uptake of VELPAR® DF (usually 60-90 days after adequate rainfall). •Before using “Tordon 101” Mixture, read and carefully observe the cautionary statements and all other information appearing on the product label. “Tordon 101” Mixture is a restricted use pesticide, for retail sale to and use only by certified applicators or persons under their direct supervision and only for those uses covered by certified applicator’s certification. SITE PREPARATION - GRID & SINGLE STEM APPLICATIONS VELPAR® DF is recommended for control of brush in site preparation. GRID APPLICATION Mix 2 2/3 pounds of VELPAR® DF with sufficient water to make one gallon of suspension and thoroughly agitate. Intermittent agitation may be required to maintain the VELPAR® DF in suspension. Apply the VELPAR® DF suspension directly to the soil surface in a grid pattern using an exact delivery handgun applicator. This equipment delivers a thin stream of predetermined volume. VELPAR® DF should be applied during the period from hardwood bud break to early summer. Application rate and grid pattern will depend on soil texture and woody plant composition. Use the lower rates on coarse textured soils and when the major component of the hardwoods are susceptible species. Use the high rates on fine-textured soils and where weeds identified in this label as “partial control or suppression” predominate. Application Patterns and Rates For VELPAR® DF Suspension ML/Spot Grid (Ft) Qt/Acre Coarse 0.6 3 X 3 3 2.0 4 X 4 6 3.1 4 X 6 6 Medium/Fine 1.6 3 X 3 8 2.8 4 X 4 8 3.5 4 X 4 10 5.2 4 X 6 10 SINGLE STEM (BASAL SOIL) Mix 2 2/3 pounds of VELPAR® DF with sufficient water to make one gallon of suspension and thoroughly agitate. Apply the VELPAR® DF suspension with an exact-delivery handgun applicator. This equipment delivers a thin stream of predetermined volume when triggered. Apply the VELPAR® DF suspension at the rate of 2 to 4 ml for each inch of stem diameter at breast height. Direct the treatment to the soil within 3 feet of the root collar of woody plants to be controlled. 10 For multi-stemmed and low-growing brush that have stem diameters that are difficult to determine, apply the DuPont™ VELPAR® DF suspension at the rate of 2 to 4 ml per 3 feet of canopy width. For tall, slender (columnar) brush types, apply 4 to 8 ml per 3 feet of height. Base the rate on whichever canopy dimension is greater (width or height). When treating brush that requires more than a single delivery of the VELPAR® DF suspension, apply subsequent deliveries equally spaced around the target plant. If treating brush on sloping sites, apply most of the suspension on the uphill side of the stem. If treating resprouts from brush disturbed by cutting or other mechanical methods, the rate of ap...
Dieses Handbuch ist für folgende Modelle:Kinderwagen - DuPontTM Velpar (79.37 kb)