Login:
Stimmen - 3, Durchschnittliche Bewertung: 3.3 ( )

Anleitung Baby Trend, modell DOUBLE SNAP N GO 1305TW

Hersteller: Baby Trend
Dateigröße: 1.77 mb
Dateiname: f20bc69f-b417-45e4-a716-622937a4abe3.pdf
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


Model # 1305TW Infant car seats not included Double Snap N Go® Instruction Manual Convenience through innovation and thoughtful design Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved. Double Snap N Go ®Double Snap N Go® WARNING: Please follow all of these instructions to ensure the safety of your children. Keep these instructions for future reference. WARNING: Failure to follow these instructions could result in serious injury or death. Avoid serious injury from falling or sliding out. Always use the infant car seat harness and insure that the child and infant car seat are properly positioned according to these instructions. WARNING: Never leave child unattended. WARNING: Care must be taken when folding and unfolding the product to prevent finger entrapment. • Purses, shopping bags, parcels, diaper bags or accessory items may change the balance of the stroller and causehazardous unstable conditions. • The maximum weight that can be carried in the storage basket is 5 lbs. The maximum weight for the parent tray is 3 lbs. • Be certain the stroller is fully erect and latched in the open position before allowing a child near the stroller. • Excessive weight may cause a hazardous unstable condition to exist. DO NOT EXCEED 45 lbs TOTAL. • For use with two (2) children weighing no more than 22 pounds each, or two children totaling no more than 44 poundscombined. Exceeding 45 lbs will cause excessive wear and stress on the stroller and may cause a hazardous, unstablecondition to exist. • DO NOT use the stroller on stairways or escalators. • NEVER allow your stroller to be used as a toy. • To clean, use only mild household soap and warm water with a sponge or cloth. • Check your stroller often for loose screws, worn parts, torn material or stitching. Replace or repair parts as needed. • Discontinue use of stroller should it malfunction or become damaged. Please contact our customer service Parts Hotline to arrange for repair or to obtain replacement parts. Please: If you experience any difficulty with the use of our product or have a question regarding these instructions, please contact our Customer Service Department at (800) 328-7363 between the hours of 8:00 and 4:30 Pacific Standard Time or visit us at Please do not return the product to the store as once it is returned it cannot be re-sold and the materials and energy used to make it are wasted. To Contact us: Baby Trend, Inc.Parts Hotline: 1567 S. Campus Ave.(800) 328-7363Ontario, CA 91761 8:00 a.m. and 4:30 p.m. Pacific Standard Time Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved. 2 Rear Axle Stroller Front Wheels (x2) PARTS ASSEMBLING 1” Bar (x 2)Flat Bar TO ENSURE SAFE OPERATION OF YOUR STROLLER, PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY AND RETAIN THEM FOR FUTURE REFERENCE. ASSEMBLY: 1. Remove stroller from box. NOTE: The front wheels, rear wheels, parent tray, and support bars specific to your infant car seats need to be installed prior to use. 2. To attach the front wheels, unfold stroller and lean backwards so that it rests on the handle and rear frame tubes with the front wheel tubes pointing upward. (Fig. 1) Position the front wheel assembly over the front tube so that the large hole in the swivel assembly will slide onto the front tube. Carefully push the wheel assembly until it locks onto the front leg. Tug on the wheel assembly to ensure that it is securely attached to the stroller. (Fig. 2) 3. Lean the stroller forward to rest on the front wheels. To attach the rear wheels, position the rear axle and wheel assembly so that the brake levers are facing the rear of the stroller. (Fig. 3.1) Press the rear wheel assembly onto the rear frame tubes, being careful that the push buttons on the forward side of each rear tube engage the hole on the forward side of each rear wheel housing. (Fig. 3.2) Tug on the rear wheel assembly to ensure that it is securely attached to the stroller and firmly locked into place. DO NOT use the stroller if the wheels are not locked into place, but rather contact our customer service department immediately at (800) 328-7363, between the hours of 8:00am and 4:30pm PST, for assistance. Fig. 1 1 2 Fig. 2 Push onto bayonet Line up the frame tubes with the axleassembly slide onto frame tubes at the same time 3 4 Push down until axle Axle housing is secure when housing snaps into place the metal tab locks axle housing into place Fig. 3 Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved. 3 WARNING: DO NOT place hot liquids in the parent tray. Hot liquids can burn your child. Do not place more than 3 pounds in the tray as it may cause a hazardous unstable condition to exist. WARNING: ALWAYS USE the Infant Car Seat harness to avoid serious injury from falling or sliding out. BRAKES: WARNING: ALWAYS SET brakes when Fig. 4 the stroller is not being pushed so that the stroller will not roll away. Never leave stroller unattended on a hill or incline as the stroller may slide down ...


Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien