Stimmen - 5, Durchschnittliche Bewertung: 3.2
(
)
)
|
Anleitung Zusammenfassung
Adult assembly is required. Tool required for assembly: Phillips screwdriver (not included). This product is intended for use indoors on carpeted surfaces. For children ages 12-36 months who are able to get on and off unassisted. Weight limit: 43 lbs. (19.05 kg). Bounce & Spin ZebraTM K0317 Please keep this instruction sheet for future reference, as it contains important information. Requires three “AAA” (LR03) alkalinebatteries (not included). Adult assembly is required. Tool required for assembly: Phillips screwdriver (not included). This product is intended for use indoors on carpeted surfaces. For children ages 12-36 months who are able to get on and off unassisted. Weight limit: 43 lbs. (19.05 kg). Bounce & Spin ZebraTM Parts #8 x 7/8” (2.2 cm) Screw - 10 Shown Actual Size Note: Tighten or loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. 6 Feet CapHandlebar 6 Base Pieces Zebra This product contains small parts in its unassembled state. Adult assembly is required. Take extra care during unpacking and assembly. CAUTION Assembly Foot Post 1 • Position the zebra upside-down. • Fit the tube end of a foot into one of the holes inside the post. • Assemble the other five feet into the post. Cap 2 3 • Insert six screws into the cap and tighten. • Turn the assembly upright. Base Piece 4 • Fit and “snap” each base piece between the spaces in the feet. Hint:The base pieces are designed to be asssembled to any of the openings between the feet, and is a one-time assembly. • Fit the cap into the center of the post. Assembly Handlebar Post 5 • While sliding the ends of the handlebar into the indents on each side of the zebra’s head, fit the post into the slot in the top of the zebra’s head. 6 • Insert four screws into the handlebar and tighten. Care • Wipe this toy with a clean cloth dampened with a mild soap and water solution. Do not immerse this toy. • This toy has no consumer serviceable parts. Do not take this toy apart. • Check the plastic parts regularly and if broken or cracked, dispose of them properly. Consumer Information Battery Installation 1.5V x 3 “AAA" (LR03) • Locate the battery compartment on the back of the handlebar. • Loosen the screws in the battery compartment door. Remove the battery compartment door. • Insert three “AAA” (LR03) alkaline batteries, as indicated inside the battery compartment. Hint:We recommend using alkalinebatteries for longer battery life. • Replace the battery compartment door and tighten the screws. • If this toy begins to operate erratically, you may need to reset the electronics. Slide the power/volume switch off and then back on. • When lights or sounds from this toy become faint or stop, it’s time for an adult to change the batteries! • Protect the environment by not disposing of this product with household waste (2002/96/EC). Check your local authority for recycling advice and facilities (Europe only). Battery Safety Information In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage: • Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). • Insert batteries as indicated inside the battery compartment. • Remove batteries during long periods of non-use. Always remove exhausted batteries from the product. Dispose of batteries safely. Do not dispose of product in a fire. The batteries inside may explode or leak. • Never short-circuit the battery terminals. • Use only batteries of the same or equivalent type, as recommended. • Do not charge non-rechargeable batteries. • Remove rechargeable batteries from the product before charging. • If removable, rechargeable batteries are used, they are only to be charged under adult supervision. FCC Statement (United States Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Consult the dealer or an experienced radio/TV technician for help. Note: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authorit...