Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
IMPORTANT – DO NOT USE THIS CABLE TO POWER ANY OTHER EQUIPMENT 1-2 AC Power You can also use an AC adapter (not included) with the following specification: 9-12V DC output, 250-300mA, centre positive. Note: Do not leave the adapter plugged in for long periods of time if the unit is not in use. 2. Preparation 2-1 Connect the unit with other MIDI equipment you may have: MIDI Sound Module MIDI IN MIDI IN MIDI IN MIDI OUT MIDI Keyboard Computer 2-2 Turn on the POWER switch. 2-3 Turn all other equipment on. 3. Setting the MIDI Transmit Channel There are 16 MIDI transmit channels available. Once you have set the unit’s MIDI channel, the unit sends all MIDI messages on this MIDI channel. Be sure to match the channel with the RECEIVE channel of any connected equipment. 3-1 Press the CHANNEL switch. The LED shows the present TRANSMIT channel 3-2 Press one (or two) of the numeric keys to change the channel. The LED changes to the pressed number. 3-3 You can also use +/- switches to increase or decrease the value. Note: * if you do nothing after step 3-1 for about 5 seconds, the LED will return to show the present PROGRAM CHANGE number. * The default CHANNEL is 1 when power is turned on. 4. Volume Control Moving the CHANNEL VOLUME slider transmits MIDI CHANNEL VOLUME messages to connected equipment. This allows you to control the volume level of the selected channel for connected devices, e.g. synthesizer, modules. 5. PITCH BEND WHEEL Moving the PITCH BEND WHEEL transmits MIDI PITCH BEND messages to any connected equipment. This allows you to bend the pitch of a sound up (or down) to add expression to your performance. 5-1 To bend the sound up: Move the WHEEL away from you. 5-2 To bend the sound down: Move the WHEEL towards you. 6. WHEEL ASSIGN Use the WHEEL to transmit MIDI CONTROL CHANGE messages. You can select and assign 119 types of MIDI functions (1-31, 33-95, 102-121, 128-132) Number Functions 1 -127 Standard MIDI controllers 128 Pitch Bend Sensitivity 129 Fine Tune 130 Coarse Tune 131 Channel Pressure 132 Velocity 6-1 Press the WHEEL ASSIGN switch and the LED starts to flash showing the number of the present MIDI controller. 6-2 Press numeric keys 0-9 to select a new MIDI controller. You can also use the +/- switches to increase or decrease the value of the number. Note: * If you do nothing for 5 seconds, the LED will return to show the current PROGRAM CHANGE number. * If the number you press is not in the range of defined numbers, the previous number will be retained. * When you assign 120 or 121 as the MIDI controller for the WHEEL, you should move the MODULATION Wheel to the mid-value then return it to the minimum value to send a relative MIDI message. 7. TRANSPOSE This function allows you to shift the pitch of the unit in semitones. You can transpose the pitch by 24 half steps (12 up, 12 down). 7-1 Press the X’POSER switch. The LED shows the current TRANSPOSE value. 7-2 Press the “+” or “-” switch to change the TRANSPOSE value. Each time you press + or -, the keyboard is transposed an additional half step. * Pressing the + and - switches simultaneously resets the pitch to the default value. Note: Turning the power off always resets the shifted pitch to the default value. 8. OCTAVE CHANGE This function allows you to shift the pitch up to three octaves higher or two lower. 8-1 Press the OCTAVE UP or DOWN to change the octave range. The LED shows the new OCTAVE value. * Press OCTAVE UP and DOWN switches simultaneously to reset the pitch to the default value. Note: if the UP or DOWN switch is not pressed for 5 seconds, the LED will return to show the PROGRAM CHANGE number. 9. Sending a PROGRAM CHANGE number Using the PROGRAM switch and the numeric keys, you can send any MIDI PROGRAM CHANGE from 0-127. 9-1 Press the PROGRAM switch. The LED starts to flash showing the current PROGRAM number. 9-2 Press the numeric keys to alter the PROGRAM CHANGE number. You can also use the “+” or “-” keys to change the value. Note: * if you don’t do anything for 5 seconds the LED stops flashing and shows the current PROGRAM CHANGE number. * if the number you press is larger than 127, it will return to the previous PROGRAM CHANGE number. 10. Sending BANK MSB and LSB message You can send any value of MSB or LSB from 0-127. 10-1 Press the CHANNEL and PROGRAM switches simultaneously. The LED starts to flash showing the current value of the LSB. Press the numeric keys to change the LSB value. You can also use the “+” or “-” switches to change the value. 10-2 Press the PROGRAM and MEMORY switches simultaneously. The LED starts to flash showing the current value of the MSB. Press numeric keys to change the MSB value. You can also use the “+” or “-” switches to change the value. Note: * if you don’t do anything for 5 seconds the LED stops flashing and shows the current PROGRAM CHANGE number. * if the number you input is over 127, it will return to the previous LSB or MSB value. 11. PROGRAM & BANK CHANGE MEMORY You can assign a selected...