Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
x 4-3/4 Long 8 1 202822 Eyebolt, 3/8-16 x 2-1/2 Long 9 6 203063 Lock Nut, 3/8-16 10 2 906206 Tank Strut 11 1 201625 Bolt,Yellow Dichromate, 5/16-18 X 3.60 Long 12 6 203218 Washer, Flat, 5/16 13 1 203099 Lock Nut, 5/16-18 14 4 204961 Bolt, Hex Head, 3/8-16 x 0.625 Long 15 6 205528 Bolt, Hex Flange, 5/16-18 x 1 Long 16 6* 203100 Nut, Hex Flange, 5/16-18 17 4 201651 Spacer .500 I.D. x .25 Long 18 2 206303 Washer 1/4 Flat 19 1 200627 Wheel Bracket 20 2 204558 Screw, Phillips, 1/4 x .375 Long, Type 25 21 1 Rim 22 1 206219 Cap, Pole Top 3” 23 1 202603 Washer, Nylon 24 2 203617 Plug Cap Item Qty. Part No. Description 25 1 522730 Label, Height Adjustment and Moving 26 1 Net 27 1 201160 Pawl Lever 28 1 801159 Ratchet 29 2 900964 Backboard Bracket 30 1 203472 Spring, Black, Slam Jam 31 1 200318 Bracket, Reinforcement, Slam Jam 32 1 900033 Bracket Slam Jam 33 4 202587 Spacer .520 I.D. x .750 O.D. x 1.0 Long 34 1 206305 Clevis Pin 1/4 x 2-3/8 Long 35 1* 206360 Bolt, Hex 3/8-16 x 2.65 Long 36 1 203796 T-Bolt, 3/8-16 x 5 Long 37 1 203470 Washer Flat, Slam Jam 38 7 206340 Lock Nut 1/2-13 39 1 203795 Nut, Special, Slam Jam 40 1 201125 Spring, Ratchet Return 41 4 206311 Spacer .520 I.D. x .750 O.D. x .50 Long 42 7 206304 Bolt 1/2-13 x 6-5/16 Long 43 4 908178 Elevator Tubes 44 1* 201129 Spacer .402 I.D. x .500 O.D. x 1.8 Long 45 1 201642 Spacer Plastic, .63 Long 46 1 281159 Handle 47 1 908176 Tube, Handle, Outer 48 1 908177 Tube, Handle, Inner * You many have extra parts with this model. 6 ID# M732201 01/06 HARDWARE IDENTIFIER (BOLTS & PINS) Item #15 (6)Item #14 (4) Item #35 (1*) Item #34 (1) Item #8 (1) Item #20 (2) Item #42 (7) Item #11 (1) Item #36 (1) HARDWARE IDENTIFIER (NUTS & WASHERS) * You may have extra parts with this model. Item #12 (6) Item #13 (1) Item #9 (1) Item #18 (2) Item #38 (7) Item #39 (1) Item #16 (6*) Item #23 (1) Item #37 (1) 7 01/06 ID# M732201 HARDWARE IDENTIFIER (STEEL SPACERS & RODS) Item #44 (1*)Item #7 (1) HARDWARE IDENTIFIER (PLASTIC SPACERS & CLIPS) Item #17 (4) Item #41 (4) Item #45 (1)Item #33 (4) HARDWARE IDENTIFIER (OTHER) Item #32 (1) Item #31 (1) Item #30 (1) Item #40 (1) 8 ID# M732201 01/06 SECTION A: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section. ITEMS REQUIRED FOR THIS SECTION (2) 1/2” and (2) 9/16" Wrenches 9/16”1/2” (2) Socket Wrenches and Sockets Tape AND/OR 1. Correctly identify each pole section and mark indicated distance from ends with tape as shown. BOTTOM POLE 43” MIDDLE POLE 43” TOP POLE 31” 4 5 6 9 01/06 ID# M732201 2. 2. While maintaining alignment, bounce middle pole section (5) into top section (4) using a wood scrap as shown until the top pole no longer moves toward the pole identification sticker on the middle pole. WOOD SCRAP (NOT SUPPLIED) 5 4 Align dimple of top pole section (4) into trough of middle pole section (5) as shown. IMPORTANT! HOLE DIMPLE middle pole THE IDENTIFICATION STICKER IS LOCATED 5" FROM THE END OF THE POLE. WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 3-1/2" MINIMUM OVERLAP, LEAVING 1-1/2" BETWEEN THE OVERLAPPING POLE AND THE IDENTIFICATION STICKER. CAUTION! 5" middle pole 1-1/2" ID STICKER 10 ID# M732201 01/06 4 5 6 WOOD SCRAP (NOT SUPPLIED) RODS SHOWN ARE FOR VISUAL REPRESENTATION OF ALIGNMENT AND ARE NOT SUPPLIED WITH THE HARDWARE Align dimple of middle pole section (5) into trough of bottom pole section (6) as shown. IMPORTANT! HOLE DIMPLE Bottom pole 5" 1-1/2" ID STICKER Bottom pole Bounce top and middle pole assembly (4 and 5) onto bottom pole section (6) using a wood scrap as shown. Bounce until the top and middle pole assembly no longer moves toward the pole identification mark on the bottom pole. 3. THE IDENTIFICATION STICKER IS LOCATED 5" FROM THE END OF THE POLE. WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 3-1/2" MINIMUM OVERLAP, LEAVING 1-1/2" BETWEEN THE OVERLAPPING POLE AND THE IDENTIFICATION STICKER. CAUTION! 4 5 6 WOOD SCRAP (NOT SUPPLIED) RODS SHOWN ARE FOR VISUAL REPRESENTATION OF ALIGNMENT AND ARE NOT SUPPLIED WITH THE HARDWARE Align dimple of middle pole section (5) into trough of bottom pole section (6) as shown. IMPORTANT! HOLE DIMPLE Bottom pole 5" 1-1/2" ID STICKER Bottom pole Bounce top and middle pole assembly (4 and 5) onto bottom pole section (6) using a wood scrap as shown. Bounce until the top and middle pole assembly no longer moves toward the pole identification mark on the bottom pole. 3. THE IDENTIFICATION STICKER IS LOCATED 5" FROM THE END OF THE POLE. WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 3-1/2" MINIMUM OVERLAP, LEAVING 1-1/2" BETWEEN THE OVERLAPPING POLE AND THE IDENTIFICATION STICKER. CAUTION! 11 01/06 ID# M732201 ID# M732201 01/06 12 4. 5. Install wheel axle (2) through wheel carriage (19) and install wheels (3) onto wheel axle (2) with spacers (17) as shown. Insert pole assembly into tank assembly as shown. Secure bottom pole (6) section to tank and wheel carriage as shown. A deep socket is recomme...