Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
BASKETBALL CENTER BASKETBALL CENTER IMPORTANT! To ensure prompt and correct handling of any problems, or to answer any questions, please contact the Sample and Display Technician at 1-800-558-5234. REQUIRED TOOLS AND MATERIALS: • Wrenches: (Two each) 7/16”, 1/2”, 9/16”, and 3/4” or Pliers • 3/16” Allen Wrench • Step Ladder, 8 ft. (2.4 m) Model 89780 SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY. This unit is intended for display purposes only and should not be used for play. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check entire box and inside all packing material for parts. Before beginning assembly, read the instructions and identify parts in this document. Proper and complete assembly, use and supervision is essential for proper operation and to reduce the risk of accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and operated properly. • During assembly, if using a ladder use extreme caution. Two people are recommended for this operation. • If technical assistance is required, contact Huffy Sports’ Sample and Display Technician. • Serious injury could occur if teeth/face come in contact with backboard, net or rim. • Display recommended for 3” (7.6 cm) or 3-1/2” (9 cm) Round or 4” (10 cm) Square poles only. • All instructions and warnings MUST accompany any display item that is sold. Most injuries are caused by misuse and/or not following instructions. Use caution when installing this unit. Internet Address: PARTS LIST Item Qty. Part No. Description 1 2 203257 Zip Tie 2 4 207103 Pole Cap for 3.5” Pole Section 3 26 203100 Nut, Hex Flange 5/16-18* 4 6 204872 Height, Decal 5 8 201611 Bolt, Hex Flange, 5/16-18 x 3” 6 16 203218 Washer, Flat, 5/16* 7 8 200516 Bolt Cover, Vinyl* 8 4 200863 POP Header Cards 9 6 200892 Plastic Push Clips 10 4 900013 3.5” Pole Section 11 1 200862 POP Insert * YOU MAY HAVE EXTRA HARDWARE P/N 211487C 04/02 2 3 P/N 211487C 04/02 Move display to location on sales floor and remove 2 X 4 runners under feet. P.O.P. Install pegboard panels onto corresponding side support railings. Secure with zip tie to temporarily hold panel in place. Remove zip ties after assembly is complete. Attach P.O.P. sign (11) with plastic push clips (9) so that it faces aisle as shown. FRONT 9 11 1 2 P/N 211487C 04/02 4 Install support railings, as shown. Insert particle board as shown and rest on second support railing. FRONT NOTE: Top shelf has square corners. TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. WARNING IMPORTANT: Top Support Railing Must Be Inserted In The Positions Shown. POP Cards Will Later Be Inserted Into Rail Slots. 3 NOTE: Location of tab on lower panel. NOTE: Use shorter bolts to assemble. TWO PEOPLE ARE NECESSARY TO MOUNT THE ELEVATOR ASSEMBLY TO THE POLE. ONE PERSON SHOULD NOT ATTEMPT TO DO THIS ALONE. WARNINGTOP VIEW FRONT D 3-1/2” Rnd. Pole 3-1/2” Rnd. Pole X 30” Pole Install enclosed pole mounting hardware and pole for each assembly. 3-1/2” Rnd. Pole 3-1/2” Rnd. Pole NOTE: A B C908811 Upper Support Railing 4 TWO PEOPLE ARE NECESSARY TO MOUNT THE ELEVATOR ASSEMBLY TO THE POLE. ONE PERSON SHOULD NOT ATTEMPT TO DO THIS ALONE. WARNINGTOP VIEW FRONT D 3-1/2” Rnd. Pole 3-1/2” Rnd. Pole X 30” Pole Install enclosed pole mounting hardware and pole for each assembly. 3-1/2” Rnd. Pole 3-1/2” Rnd. Pole NOTE: A B C908811 Upper Support Railing 4 Enclosed One Set Of Hardware For (Each) Pole Installation P/N 211487C 04/02 5 Assemble display products per diagram below and procedures on following pages for each model. Then mount to corresponding backboard hardware. INSTALLATION DIAGRAM FRONT TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. WARNINGMOUNTING THE ELEVATOR ASSEMBLY TO THE POLE IS PERFORMED AT AN ELEVATED HEIGHT. USE PROPER PRECAUTION. WARNING73092 44” Fan Backboard w/Slam Jam Rim 89036 44” SFA w/Slam Jam Rim Steel Framed Acrylic 81410 48” Fan Backboard w/Slam Jam Rim C B LINE-UP CLEAR SLAM FREE STYLE HUFFY TUFF D A 5 80550 44” Fan w/Standard Rim P/N 211487C 04/02 6 Mount extension arm and rim to backboard and finger tighten. NOTE: For spring loaded rim assembly, refer to instructions included with rim hardware. Refer To Combo For Goal Assembly Instructions A B 1. Pole Locations Mount extension arm and rim to backboard and finger tighten. NOTE: For spring loaded rim assembly, refer to instructions included with rim hardware. Refer To Combo For Goal Assembly Instructions A B 1. Pole Locations 2. 95662103 Secure hardware to extension arm as shown and tighten completely. install pole cap (2) P/N 211487C 04/02 7 P/N 211487C 04/02 8 Insert header cards (8) into place as shown. 8 6 BASKETBALL CENTER BASKETBALL C...