Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
•If removable rechargeable batteries are used, they are only to be charged under adult supervision. •Rechargeable batteries are to be removed from the product before they are charged. •If you use a battery charger, it should be examined regularly for damage to the cord, plug, enclosure and other parts. Do not use a damaged battery charger until it has been properly repaired. •Low battery power in the toy bar may cause it to operate erratically (no sounds/no lights/no bubbling action) and the toy bar may not turn off. If this should happen, remove and discard all three batteries in the large battery compartment and replace with three, new “D” (LR20) alkaline batteries. 5 Assembly This package contains small parts in its unassembled state. Adult assembly is required. CAUTION Assembly This package contains small parts in its unassembled state. Adult assembly is required. CAUTION •Place the base tube on a flat surface as shown. •Position the left and right base wires as shown. Note the location of the colored tab on the left and right base wires. •Fit the left base wire into the base tube. •Fit the right base wire into the base tube. Base Tube Left Base Wire Colored Tabs Right Base Wire 1 Back View Base Tube Base Wire Colored Tab • Make sure both colored tabs on the base wires are visible through the holes in the base tube. 6 Assembly 2 Electronic Unit Battery Compartment Doors Up FlexBaseWiresInward Tab Tab Assembly 2 Electronic Unit Battery Compartment Doors Up FlexBaseWiresInward Tab Tab •Position the footrest so that the electronic unit battery compartment doors are upright. •While flexing the base wires toward each other, hook the footrest onto the ends of the base wires. •Push the footrest down completely to the tabs on the base wires. 7 Assembly 3 Base Wire Base Wire Seat Back Tube Bends Backward Retainers Assembly 3 Base Wire Base Wire Seat Back Tube Bends Backward Retainers •Position the seat back tube so that it bends backward. •Fit the seat back tube completely onto the base wires. •Fit a retainer (rounded side inward) to one end of the seat back tube. • Insert a screw through the outside hole in the seat back tube and into the retainer. •While holding the retainer in place, tighten the screw with a Phillips screwdriver. Do not over-tighten. •Repeat this procedure to secure the other side of the seat back tube to the base assembly using the remaining retainer and screw. 8 Assembly 4 Pull Up Assembly 4 Pull Up •Pull the seat back tube up to be sure it is secure. If you can remove either end of the seat back tube, you have not assembled it correctly. Remove the screws and retainers. Re-read and repeat Assembly steps 3 and 4. 9 •Unbuckle the restraint belts from the restraint pad. Push the restraint belts back through the slots in the pad . Assembly 5 Seat Back Tube Pad Footrest B Assembly 5 Seat Back Tube Pad Footrest B •Fit the pad upper pocket onto the seat back tube • Lift the footrest. Fit the pad lower pocket onto the footrest . Lower the footrest. .B 10 Assembly 6 Restraint Belts Assembly 6 Restraint Belts •Fit both restraint belts back through the pad slots, as shown. 11 Assembly 12 7 • Fit the ends of the toy bar into the sockets in the footrest. Assembly is now complete. • The toy bar is removable. Simply lift up to remove. Hint: The square end of the toy bar fits into the square socket and the circular end of the toy bar fits into the circular socket. Set-Up & Use To prevent serious injury and/or falls: •Never use on any elevated surface, since child’s movement may cause bouncer to slide or tip over. •Never use as a carrier or lift while child is seated. • Always use the restraint system. •Never leave child unattended. •Never use with a child able to sit up unassisted. WARNING 1 Restraint Belt Buckle Restraint Pad Set-Up & Use To prevent serious injury and/or falls: •Never use on any elevated surface, since child’s movement may cause bouncer to slide or tip over. •Never use as a carrier or lift while child is seated. • Always use the restraint system. •Never leave child unattended. •Never use with a child able to sit up unassisted. WARNING 1 Restraint Belt Buckle Restraint Pad Securing Your Child •If the toy bar is attached, remove it before placing your child in the seat. •Place your child in the seat. Position the restraint between your child’s legs. •Fasten both restraint belts to the buckles on each side of the restraint pad. Make sure you hear a “click” on both sides. •Check to be sure the restraint is securely attached by pulling it away from your child. The restraint should remain attached. •Attach the toy bar, if desired (see Assembly step 7). 13 Loosen To tighten the belts: •Feed the anchored end of the belt up through the buckle to form a loop . •Pull the free end of the belt . •Repeat this procedure to tighten the other belt. To loosen the belts: •Feed the free end of the belt up through the buckle to form a loop . Enlarge the loop by pulling on the end of the loop toward the buckl...