Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
Tighten the buckled belt by pushing down hard on the infant restraint and pulling hard on the shoulder belt. . inch . 2. While pushing down on infant restraint, pinch the two straps together behind the buckle tongue. Unbuckle the belt without allowing it to slip. 3. Connect lap and shoulder belts with locking clip as shown . and ... 4. Rebuckle belt. Check that lap belt does not move by pulling and pushing hard on infant restraint. If belt loosens or lengthens, repeat procedure. .. Locking clip goes here, 1/2 inch from the buckle 25 5.3 LATCH locations Newer vehicles may have one or more seating positions with LATCH anchorage systems. If vehicle is equipped with LATCH, the vehicle lower anchor points may be visible at the vehicle seat crease. If not visible, they may be marked with the symbol . See your vehicle owner’s manual for exact locations, anchor identification, and requirements for use with an infant restraint. Typical seat in a passenger vehicle. Other vehicle types may have different LATCH locations or different markings. Vehicle Seat Crease Vehicle Lower Anchor Points LATCH is defined as anchorages 280mm (11.02 inches) on center. As a manufacturer, we do not recommend using the LATCH system in the center position if it exceeds this length. 26 6.0 Using Infant Restraint 6.1 Positioning Harness Straps FAILURE TO PROPERLY ADJUST THE HARNESS STRAPS FOR YOUR CHILD INCREASES THE RISK OF SERIOUS INJURY OR DEATH IN THE EVENT OF A SHARP TURN, SUDDEN STOP OR CRASH. The harness straps must be properly adjusted to fit your child according to the following instructions. 1. Remove infant restraint from base and rotate handle down to sitting position. See “3.3 Removing and Attaching Base” and “3.4 Adjusting Handle”, p. 13. 2. Place child in infant restraint as shown ... 3. Determine which pair of harness slots are even with or just below your child’s shoulders ... DO NOT use upper harness slots if they are above your child’s shoulders. They will not hold a small child securely in a sudden stop or crash. .. 4. If the harness straps must be adjusted: remove child from infant restraint and follow directions for your type of harness system: .. 6.1.1 3-Point Harness - p. 28 Use harness slots even with or just below 6.1.2 5-Point Harness - p. 29 child’s shoulders 27 6.1.1 3-Point Harness 1. From back, push harness anchor buckle back through harness slot. If necessary, from front, use harness strap to pull buckle from slot ... Harness tightener buckle 2. Reinsert harness anchor buckle in the appropriate slot ... 3. From back, remove harness strap from harness tightener. If necessary, from front, use harness strap to pull strap from slot. .. Harness anchor .... 4. Reinsert strap in the appropriate slot. Thread strap through tightener exactly as shown ... 5. SAFETY CHECK: a) CHECK that straps are not twisted; . b) CHECK that straps are secure: pull on harness straps from front. c) CHECK that harness anchor buckle is snapped flat against back as shown ... 28 6.1.2 5-Point Harness 1. Depress the harness adjustment button under the seat flap ... Pull the shoulder straps out to loosen the harness. 2. Behind seat, remove the ends of the two shoulder straps from the metal junction plate ... 3. From front, pull straps through the harness slots and then reinsert them through the appropriate slots. 4. Behind seat, push both shoulder straps UNDER owner’s manual pocket and out the bottom. 5. Reassemble the strap ends onto the metal junction plate ... Follow the appropriate instructions for a smaller or larger baby on the following page. . Harness adjustment button .. 6. SAFETY CHECK: After the harness has been completely reinstalled, a) CHECK that harness straps are not twisted in front or back. b) CHECK that straps are secure by pulling on them. 29 FOR SMALLER BABY: Use the lower harness slots . (if they are even with or just below your child’s shoulders) and the upper strap loops ... The ends of the straps must hang in front of the metal plate as shown in .., not as shown in ... ...... CHECK that the loops are completely within junction plate slots ... CHECK that straps are secure by pulling on them. .. FOR LARGER BABY: Use upper harness slots and the end strap loops ... CHECK that the loops are completely within junction plate slots ... CHECK that straps are secure by pulling on them. 30 .... 6.2 Securing Child in Infant Restraint Failure to properly secure your child in the infant restraint/carrier increases the risk of serious injury or death from suffocation or falls, or in the event of a sudden stop or crash. Even when used only as a carrier, make sure the harness straps are properly secured. 1. Move infant restraint handle to sitting position (see page 13). 2. Open harness clip by . squeezing both sides and unbuckle as shown ... OR 3. Place your child in the infant restraint as shown in , not ... Pull the harness straps down over your child. 4. Follow directions for your harness: 6.2.1 3-Point Harness: p. 32 6.2.2 5-Point ...