Stimmen - 5, Durchschnittliche Bewertung: 4.4
(
)
)
|
Anleitung Zusammenfassung
Keep these instructions for future reference. If you are missing parts, or need assistance, please call (800) 344-BABY. WARNING Suffocation and Strangulation Hazard. Death or Serious Injury Can Occur. Infants who cannot get in and out of an adult bed without help can be trapped between a mattress and a wall and suffocate. NEVER place infants in adult beds with or without a bed rail. BED RAIL USE: • Bed rail can trap young children against mattress, headboard, or footboard. • Use only for children who have outgrown a crib. NEVER use in place of a crib. • Use only with children who can get in and out of an adult bed without help (typically 2 years and up). • ALWAYS keep bed rail pushed firmly against mattress and at least 9 inches from headboard and footboard. • NEVER use on a toddler bed, bunk bed, water bed, or bed with inflatable mattress. Use only on adult bed with mattress and box spring. 1 Contents Contents ABCDEFG A. Bedrail B. Cross Rail Assembly Pieces C. Safety Strap with Anchor D. Cup Holder E. Nightlight F. Substitute Clip G. Pocket Flap Assembly Instructions 132 2 Assembling the Cross Rails Depress the Locking Pin on one half and push it into the other half of the rail. The Locking Pin pops into place when the pieces are securely attached, as shown in Fig. 1. Repeat for the second Cross Rail. Locking Pin Fig. 1 Installing the Cross Rails Detach the 2 Pocket Flaps on both sides of the Bedrail. Insert the Cross Rails into the middle and bottom pockets, as shown in Fig. 2. Starting from the left side of the Bedrail, slide the small end of the Cross Rail into the pocket. Depress the Locking Pin and push into the Receiver on the right side of the Bedrail. The Locking Pin pops into place when the pieces are securely attached. To secure the left side of the Cross Rail into the corresponding Receiver, first depress the Locking Pin, then pull back on the Locking Piece as shown in Fig. 3. Insert the Cross Rail into the Receiver and push the Locking Piece forward as shown in Fig. 4. The Locking Pin pops into place when the pieces are securely attached. Re-attach the 2 Pocket Flaps when finished. Repeat steps for the bottom Cross Rail. Fig. 2 Pull Back Depress locking pin Fig. 3 Push Forward Fig. 4 3 Installation Instructions Installation Instructions Installing the Bedrail As shown in Fig 5, unlock the Locking Buckle that holds the Safety Straps in place. Repeat on the other side. The Locking Buckles should remain unlocked as you install the Bedrail onto the mattress. Unbind the Safety Straps. It may seem that you have an excessive amount of strap for the size of the mattress but this will be taken care of in the final adjustment step. Lift the mattress slightly and slide both legs of the Bedrail between the mattress and the box spring. The Bedrail must be oriented 9 inches from the head of the bed, Fig. 5 as shown in Fig. 6. Please refer to the ruler printed along the side of the instruction page for accurate measurement. With the help of a second person, lift the mattress sufficiently to extend the Safety Straps to the opposite side of the bed. Make sure that the Safety Straps are not twisted or tangled and make sure that the Anchors are facing up. Bring the mattress back down. Check that the Bedrail is still 9 inches from the head of the bed and make any necessary adjustments. Tightening the Safety Straps To secure the Bedrail against the side of the mattress Fig. 6 pull the loose end of the Safety Strap that is protruding from the Bedrail, as shown in Fig. 7. Pull the Safety Strap towards you until the Anchor is flush against the mattress on the opposite side. If the Safety Strap does not pull through smoothly it is most likely twisted under the mattress. Correct this before continuing. Once the Anchor is flush with the mattress insure that the smooth part of the Anchor is directly under the mattress while the ridged part is snug against the side of the mattress, as shown in Fig. 8. It is critical that the Safety Straps with Anchors be pulled very tight against the side of the mattress. To do so, pull on the Safety Strap until the Anchor creates significant indentations in the mattress, as shown in Fig. 8. Fig. 7 You may need to pull on the Safety Strap several times in order to get the required tightness. Once sufficiently tight, continue to pull the Safety Strap with one hand while locking the Locking Buckle with the other. Ensure that no slack was created in the process of locking the Locking Buckle. Check to make sure that the process of tightening did not cause the mattress to bow and that the mattress still lays flat against the box spring. Once sufficiently tight, repeat the steps to tighten the Safety Strap on the other side. Check for Correct Installation Fig. 8 The mesh panel of the Bedrail and the Anchors should be firmly against the sides of the mattress with no gaps. To check for tightness of the Bedrail, place your hand Locking Buckle in Unlock Position 9” Locking Buckle Loose end of Safet...