Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
5. Press A to exit the setting screen. 3 Operation Guide 3078 Alarm on indicator Snooze alarm indicator Alarm Operation The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the watch is in. In the case of the snooze alarm, the alarm operation is performed a total of seven times, every five minutes, until you turn the alarm off. • Alarm and Hourly Time Signal operations are performed in accordance with the Timekeeping Mode time. • To stop the alarm tone after it starts to sound, press any button. • Performing any one of the following operations during a 5-minute interval between snooze alarms cancels the current snooze alarm operation. Displaying the Timekeeping Mode setting screen Displaying the setting screen To test the alarm In the Alarm Mode, hold down D to sound the alarm. To turn an alarm on and off 1. In the Alarm Mode, use D and B to select an alarm. 2. Press A to toggle it on and off. • Turning on a alarm ( , , or ) displays the alarm on indicator on its Alarm Mode screen. • Turning on the snooze alarm ( ) displays the alarm on indicator and snooze alarm indicator on the Alarm Mode snooze alarm screen. • In all modes, the alarm on indicator is shown for any alarm that is currently turned on. • The alarm on indicator flashes while the alarm is sounding. • The snooze alarm indicator flashes while the snooze alarm is sounding and during the 5-minute intervals between alarms. To turn the Hourly Time Signal on and off 1. In the Alarm Mode, use D to select the Hourly Time Signal ( ). 2. Press A to toggle it on and off. • The Hourly Time Signal on indicator is shown on the display in all modes while this function is turned on. Auto light switch indicator Hourly time signal on indicator Illumination This watch has two EL (electro-luminescent) panels that cause the entire display to glow for easy reading in the dark. The watch’s auto light switch turns on illumination automatically when you angle the watch for reading towards your face. • The auto light switch must be turned on (indicated by the auto light switch indicator) for it to operate. • See “Illumination Precautions” for more important information. Parallel to ground More than 40° To illuminate the display In any mode, press L to turn on illumination. • The above operation turns on illumination regardless of the current auto light switch setting. • You can use the procedure below to select either 1.5 seconds or 3 seconds as the illumination duration. When you press L, the illumination will remain on for about 1.5 seconds or 3 seconds, depending on the current illumination duration setting. To specify the illumination duration 1. In the Timekeeping Mode, hold down A until the seconds start to flash, which indicates the setting screen. 2. While the seconds are flashing, press B to toggle the setting between 1.5 seconds ( ) and 3 seconds ( ). 3. Press A to exit the setting screen. About the Auto Light Switch While the auto light switch is enabled, illumination turns on whenever you position your wrist as described below in any mode. Moving the watch to a position that is parallel to the ground and then tilting it towards you at more than 40 degrees causes illumination to turn on. • Wear the watch on the outside of your wrist. Warning! • Always make sure you are in a safe place whenever you are reading the watch using the auto light switch. Be especially careful when running or engaged in any other activity that can result in accident or injury. Also take care that sudden illumination by the auto light switch does not startle or distract others around you. • When you are wearing the watch, make sure that its auto light switch is turned off before riding on a bicycle or operating a motorcycle or any other motor vehicle. Sudden and unintended operation of the auto light switch can create a distraction, which can result in a traffic accident and serious personal injury. To turn the auto light switch on and off In the Timekeeping Mode, hold down B for about three seconds to toggle the auto light switch on (auto light switch indicator displayed) or off (auto light switch indicator not displayed). • The auto light switch indicator is on the display in all modes while the auto light switch is turned on. • In order to protect against running down the battery, the auto light switch turns off automatically approximately six hours after you turn it on. Reference This section contains more detailed and technical information about watch operation. It also contains important precautions and notes about the various features and functions of this watch. Graphic Areas There are two graphic areas named A and B. The information shown in each graphic area depends on the current mode. Graphic area A Graphic area B • The following table shows the information that appears in graphic areas A and B. Flash Alert When Flash Alert is turned on, the illumination flashes for the alarms, the Hourly Time Signal, the countdown alarm, and stopwatch auto start....