Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
CONTROLS 1 ALARM 1, ALARM 2 – RADIO activates the radio for alarm 1 or alarm 2 – BUZ activates the buzzer for alarm 1 or alarm 2 – OFF switches off the alarm 1 or alarm 2 2 Clock control -SET TIME : sets the clock time -CLOCK: to run on clock time -SET AL 1: sets the alarm time for alarm 1 -SET AL 2: sets the alarm time for alarm 2 3 UP / DOWN: adjusts the hours/ minutes for the clock and alarm times 4 DISPLAY - show the clock/ alarm times and status of the set 5 Battery door -opens to store a 9 volt 6F22 type battery (not included) for clock memory backup 6 VOL - adjusts the sound level 7 Frequency indicator - shows the radio frequency of your selected waveband 8 BAND (MW/FM/AUX) - select MW/FM waveband or switch to the AUX source 9 TUNING - tunes to radio stations 0 REPEAT ALARM (SLEEP OFF) -switches off the active alarm for a 6-7 minute period -switches off the radio sleep function ! SLEEP -activates the radio for sleep function -adjusts the sleep period @ ALARM RESET -stops the active alarm for 24 hours # RADIO ON/OFF -switches the radio on/off $ BRIGHTNESS -changes the brightness of the display illumination % Mains lead -for AC mains supply ^ Pigtail aerial -improves FM reception & AUX -connects external audio source. INSTALLATION POWER SUPPLY 1 Check if the mains supply, as shown on the type plate located on the bottom of the set, corresponds to your local mains supply. If it does not, consult your dealer or service centre. 2 Connect the mains lead to the wall socket. 3 To disconnect the set from the mains supply completely, remove the plug from the wall socket. CLOCK MEMORY BACKUP The clock memory backup allows your alarm and clock time settings to be stored for up to a day when there is a power interruption e.g. mains failure. The complete clock radio and display illumination will be switched off. As soon as the mains supply returns, the display will indicate the correct time. 1 Remove the battery door to insert a 9 volt 6F22 type battery (not included) for backup. 2 Replace the battery door. NOTE: If no backup battery is installed or the power interruption is prolonged, you will need to set the clock and alarm times again. Batteries contain chemical substances so should be disposed of properly. For users in the U.K.: please follow the instructions on the reverse of this sheet. The type plate is located on the bottom of the set. ILLUMINATION BRIGHTNESS Adjust the BRIGHTNESS switch to HI or LO – HI to increase the brightness – LO to select low illumination RADIO You can use this set solely as a radio! 1 Adjust RADIO ON/OFF to ON to switch on the radio. 2 Select your waveband by adjusting the BAND switch. 3 Adjust TUNING to tune to your desired station. 4 Turn the VOLUME control to adjust the volume level. 5 Adjust RADIO ON/OFF to OFF to switch off the radio. To improve reception: FM: extend and position the pigtail for optimum reception. MW: uses a built-in aerial inside the set. Direct the aerial by adjusting the position of your set. SETTING THE CLOCK AND ALARM TIME The time is displayed using the 24-hour clock IMPORTANT! To adjust the clock and alarm times accurately, always make sure you press UP / DOWN separately and not simultaneously. 1 Turn the clock control to SET TIME or SET AL 1 or SET AL 2 to set the clock or alarm time respectively. 2 Press UP / DOWN repeatedly or hold down on the respective button to adjust the hours and minutes. 3 Release UP / DOWN when you reach the correct setting. 4 After you have set both the hour and minutes, turn the clock control to CLOCK to run on clock time. SELECTING THE ALARM MODE GENERAL If you wish to use the alarm, you must first set the alarm time first. You can choose from two different alarm modes to wake you up: by radio or buzzer. • Select your choice of alarm mode by adjusting AL 1 or AL 2 to RADIO or BUZ. ™ The buzzers are at a set volume and cannot be adjusted. BUZ on AL 1 is a low tone buzzer while BUZ on AL 2 is a high tone. SWITCHING OFF THE ALARM There are three ways of switching off the alarm. Unless you cancel the alarm completely, the 24 hour alarm reset option will be automatically selected after 59 minutes, from the time your alarm time first goes off. 24 HOUR ALARM RESET If you want the alarm mode to be stopped immediately but also wish to retain the same alarm setting for the following day: • Press ALARM RESET during the alarm call. CANCELING THE ALARM COMPLETELY To cancel the set alarm time before it goes off, or during the alarm call: • Adjust AL 1 or AL 2 to OFF position. REPEAT ALARM This repeats your alarm call at 6-7-minute intervals. • During the alarm call, press REPEAT ALARM. SLEEP About Sleep This set has a built-in timer which enables the set to be automatically switched off during radio playback after a set period of time. This allows you to lie back, listen and fall asleep. The maximum sleep time is 59 minutes. Setting SLEEP 1 Check that both the clock control is in CLOCK position and the radio is switched off. 2 To set the...