Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
1 ) 1 SET TIME /ALARM SET -sets the clock time -sets the alarm time 2 HR / MIN -adjusts the hours / minutes for clock / alarm / sleep time 3 REPEAT ALARM / SLEEP OFF -switches off the active alarm for a 9 minutes period -switches off the radio sleep function 4 ALARM RESET -stops the active alarm for 24 hours 5 SLEEP -activates the radio for sleep function -adjusts the sleep period 6 TUNING - tunes to radio stations 7 ALARM indicator - lights up when alarm is activated. 8 FM/MW -selects FM/MW waveband 9 VOLUME - adjusts the sound level 0 RADIO / ALARM OFF: switches off the radio/alarm RADIO ON: switches on the radio ALARM - RADIO: activates the radio for alarm ALARM - BUZZER: activates the buzzer for alarm ! Power cord -connects to wall outlet @ Pigtail - improve FM reception # Battery door - opens to store a 9 volts 6F22 battery (not included) for clock memory backup. INSTALLATION POWER SUPPLY 1 Check if the power supply, as shown on the type plate located on the bottom of the set, corresponds to your local power supply. If it does not, consult your dealer or service center. 2 Connect the power cord to the wall outlet. 3 To disconnect the set from the power supply completely, remove the plug from the wall outlet. For users in the U.K.: please follow the instructions on the lower left handed corner of the sheet. CLOCK MEMORY BACKUP The clock memory backup allows your alarm and clock time settings to be stored for up to a day when there is a power interruption e.g. power failure. The complete clock radio and display illumination will be switched off. As soon as the power supply returns, the display will indicate the correct time. 1 Remove the battery door to insert a 9 volts 6F22 type battery (not included) for backup. 2 Replace the battery door. NOTE: If no backup battery is installed or the power interruption is prolonged, you will need to set the clock and alarm times again. Batteries contain chemical substances so they should be disposed of properly. Standby power consumption ..........................................................................1.8 W RADIO You can use this set solely as a radio! 1 Adjust RADIO / ALARM to RADIO ON to switch on the radio. 2 Select your waveband by adjusting the FM/MW switch. 3 Adjust TUNING to tune to your desired station. 4 Turn the VOLUME control to adjust the volume level. 5 Adjust RADIO / ALARM to OFF to switch off the radio. • When sleep function is activated, to switch off the radio, you also need to press SLEEP OFF button. To improve reception: FM: Extend and position the pigtail fully to obtain optimal reception. MW: uses a built-in antenna inside the set. Direct the antenna by adjusting the position of your set. SETTING THE CLOCK / ALARM TIME The time is displayed using the 24-hour clock. 1 Hold down SET TIME / ALARM SET. 2 Press HR or MIN repeatedly, or hold down HR or MIN to adjust minute and/or hour. 3 Release SET TIME / ALARM SET and HR or MIN when you reach the correct setting. ™ The set clock time will show on the display and start to run. SELECTING THE ALARM MODE To use the alarm, you must set the alarm time first. You can choose from two different alarm modes to wake you up: by radio or buzzer. 1 Select your choice of alarm mode by adjusting RADIO / ALARM to RADIO or BUZZER. ™ The alarm indicator (AL) will light up. Helpful Hint: • If you have selected the radio mode, make sure you have adjusted the volume loud enough to wake you. • The buzzer is set at a fixed volume and cannot be adjusted. SWITCHING OFF THE ALARM There are three ways of switching off the alarm. Unless you cancel the alarm completely, the 24 hour alarm reset option will be automatically selected after 59 minutes, from the time your alarm time first goes off. 24 HOUR ALARM RESET If you want the alarm mode to be stopped immediately but also wish to retain the same alarm setting for the following day: • Press ALARM RESET during the alarm call. ™ The alarm indicator (AL) will remain on. CANCELING THE ALARM COMPLETELY To cancel the set alarm time before it goes off, or during the alarm call: • Adjust RADIO / ALARM to OFF position. ™ The alarm indicator (AL) will light off. REPEAT ALARM This repeats your alarm call at 9-minute intervals. 1 During the alarm call, press REPEAT ALARM. 2 Repeat if desired for up to 59 minutes. ™ The alarm indicator (AL) will remain on. SLEEP This set has a built-in timer which enables the set to be automatically switched off during radio playback after a set period of time. This allows you to lie back, listen and fall asleep. The maximum sleep time is 1 hour and 59 minutes. Setting SLEEP 1 Set RADIO / ALARM to OFF position. 2 Set the sleep time to activate sleep function by selecting on the following ways: • Simply press SLEEP to set your sleep time to 59 minutes. • Hold down SLEEP, and press MIN repeatedly to adjust sleep time from 59 minutes downward. • Hold down SLEEP and press HR to get one more hour sleep time (1:59) ™ To cancel sleep, press SLEEP OFF. SAFE...