Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
TUNING TO RADIO STATONS Automatic tuning •Press TUNING +/- one second or more to tune to your station. ™The radio automatically tunes to a station of sufficient reception. Manual tuning •Press TUNING +/- briefly or repeatedly until you reach the desired frequency. Helpful hints: – If you have selected AL 1 (AL ), make sure you have properly tuned to a station before turning off the set. – If you set and activate the same time for both alarms, only the AL 2 (AL ) will be activate at the set time. – When both AL 1 (AL ) and AL 2 (AL ) are turned on, by default the display shows the alarm time nearest to activation. – To check the alarm time setting for AL 1 or AL 2, press AL 1 or AL 2 button. – It is not possible to adjust the alarm time during an alarm call or the repeat alarm mode. SWITCHING OFF THE ALARM There are three ways of switching off the alarm. Unless you cancel the alarm completely, the 24-hour ALARM RESET will be automatically selected after 59 minutes from the time your alarm first goes off. 24 HOUR ALARM RESET If you want the alarm mode to be stopped immediately but also wish to retain the same alarm setting for the following day: • Press ALARM RESET / SLEEP. ™ You will hear a beep tone confirming 24 hour reset activation. REPEAT ALARM This repeats your alarm call at 9 minute intervals. • During the alarm call, press REPEAT ALARM / BRIGHTNESS CONTROL.. ™ Display shows (AL ) or (AL ) flashing during a repeat alarm. • Repeat if desired (up to a maximum of 6 times). CANCELING THE ALARM COMPLETELY • Press AL 1 or AL 2 button once or more until the OFF appears under the respective (AL ) or (AL ) icon. SLEEP (See 6) About Sleep This set has a built-in sleep timer, which enables the radio to be automatically switched off after a set period of time. There are four sleep time options. Setting and switching off SLEEP 1 Within 1 second, press ALARM RESET / SLEEP twice until the display shows SLEEP and SL: 60. ™ The radio is automatically switched on and tunes to the last station. 2 To select other sleep time options, press ALARM RESET / SLEEP again within 1 second before the display returns to clock time. ™ The display shows in sequence: SL : 30, SL : 15 and OFF. 3 To cancel sleep, press either: – RADIO ON/OFF – REPEAT ALARM / BRIGHTNESS CONTROL. – ALARM RESET / SLEEP once or more until SLEEP disappears from the display. USING THE PROJECTION You may have the experience of looking for a clock in the darkness. With this projection feature, you can conveniently project the clock time onto a surface e.g. walls ceiling (furniture, glasses not recommended). 1 Press PROJECTION ON/OFF to switch on. ™ The Projection lens lights up red. 2 Turn the Projection lens wheel (maximum 180 degree left or right) and also the set, if necessary, to find a suitable projection surface. (See 7) 3 To change the projected time upside down, press REVERSE PROJECTION. 4. To change the projection slightly to a different angle, turn the ROTATE PROJECTION ball (maximum 75 degree left or right.). 5. Press PROJECTION ON/OFF to switch off. ™ The Projection lens goes out. TROUBLESHOOTING If a fault occurs, first check the points listed below before taking the set for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre. WARNING: Under no circumstances should you try to repair the set yourself, as this will invalidate the guarantee. Do not open the set as there is a risk of electric shock! No sound – Volume not adjusted • Adjust the volume No display backlight / display malfunction/ radio and alarm do not function – Set is in Power Low mode • Connect AC/DC adapter or insert fresh batteries Display error / no reaction to any controls – Electrostatic discharge • Press the RESET hole on the bottom of the set with a ball-pen. Or disconnect set from AC/DC adaptor and batteries for 5 minutes, then re-plug. Continuous crackling and hiss noise during MW reception – Interference from other electrical equipment e.g. TVs, computers, fluorescent lamps •Move the clock radio away from electrical equipment Intermittent crackling sound during FM reception – Weak signal • Extend and position the pigtail aerial Helpful hints: – When battery-powered, the projection lens lights up briefly to help save energy. – To a longer projection time, please use the supplied 7.5V AC adapter to oper ate the set. MAINTENANCE & SAFETY • If you do not intend to use set for a long time, remove the batteries. • Do not expose the set to humidity, rain, sand or excessive heat caused by heating equipment or direct sunlight. • To clean your set, use a soft damp cloth or chamois leather. Do not use cleaning products, which contain benzene, thinner, etc. as these may harm the housing. ENVIROMENTAL INFORMATION We have reduced the packaging to its minimum using only paper and cardboard. Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe local regulations on the disposal of...