Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
By employing the most sophisticated digital and optical technologies, the compact disc not only offers the ultimate in sound reproduction, it also provides operating features which have never been seen before in audio equipment designed for home, such as fast access to any track on the disc, very simple programming and armchair control. Please read this manual thoroughly. It will explain the features and operation of your CD Player and help to ensure a trouble free installation. Please unpack your CD Player carefully. We recommend that you save the carton and packing material, as they will be helpful should you ever need to move your unit or return it for service. Your CD Player is designed to work in a horizontal position and it is important to allow at least two inches of space behind the unit for adequate ventilation and for the cables. To avoid damage, never place the unit near SAFETYINFORMATION This CD player is designed to operate on 220-240 Volts 50Hz AC or 110-120 Volts 60 Hz AC. Normally the equipment is supplied with a mains lead with a fitted 3 pin plug suitable for the country it is to be used in. If the plug needs to be changed, please follow the instructions below. PLUGFITTINGINSTRUCTIONS The wires in the mains lead are coloured in accordance with the following code: Blue -Neutral Brown -Live Green / Yellow -Earth In the UK the wires must be connected to the terminals in the plug as follows: Blue -N or Black Brown -L or Red Green / Yellow -E or Earth N L E Brown to Live Blue to Neutral Plug NOTE 1. If a 13-amp plug is used, in the UK it must be fitted with a 3 Amp fuse. 2. If a 3-pin plug with earthing contact is used, the Green/Yellow wire must be connected to the E terminal. TO ACHIEVE MAXIMUM PERFORMANCE FROM YOUR CD PLAYER: 1. Install the equipment in a location which is relatively free of moisture and dust, and which is well ventilated. 2. Avoid installing the equipment in a location exposed to direct sunlight or extreme heat (such as above a heater or radiator). 3. The equipment may not be able to perform at its best in an extremely cold or hot environment. Do not attempt to use below 41oF/5oC or above 95oF/35oC. 4. Always handle discs with clean hands. Avoid using scratched discs.. 5. Keep this manual in a safe place for future reference. 6. Do not attempt to clean the CD player or CD discs with chemical solvents, as this may cause irreparable damage. Use a clean, dry cloth, or specially designed cleaning materials for discs. 7. If the CD player malfunctions, do not openthe unit and attempt to repair it yourself. This is a highly technical product and requires specialist service - return it to your dealer. 8. Use batteries (2 x AAA) of the same type in the remote control handset. The use of odd or different type cells will affect its 3. As with all electrical equipment, it is recommended that the mains plug is removed from the wall socket when not in use. UK ONLY: FOR ADDED SAFETY, WHEN CONNECTING THE AC MAINS LEAD TO A 3 PIN PLUG USE A 3A FUSE APPROVED BY ASTA TO BS1362 - WITH ASA MARK CD43 mk2 Compact Disc Player SAFETYWARNINGS THE CD PLAYER SHOULD NOT BE REPAIRED BY ANYONE EXCEPT QUALIFIED SERVICE PERSONNEL. SPECIFICATION Power requirements AC 220-240 V 50 Hz Power Fuse rating T 250 mA or: AC 110-120 V 60 Hz T 500 mA Power consumption 16 Watts max Frequency response 1 Hz - 20 kHz ± 0.5 dB Output level 2.2 V RMS at 1kHz, 0 dB Output impedance 600 . .. , ,, min load 10 k. .. Laser type Semiconductor ALGaAs Wavelength 790 nm ± 25 nm Light output (cw) 0.18 mW typical Signal to noise ratio better than 96 dB Dynamic range better than 100 dB Number of channels 2 Total harmonic distortion < 0.01% at 1 kHz, 0 dB Dimensions 420 x 60 x 200 mm CAUTION! CAUTION Invisible laser radiation when top cover isPERFORMING removed. ADJUSTMENTS OR PROCEDURES OTHER THAN THOSE SPECIFIED HERE MAY RESULT IN HAZARDOUS EXPOSURE. OTHER FEATURES 1. Infra-red remote control. 2. High precision 24 bit, .. digital to analogue conversion. 3. 128 Fs filter. 4. 3-beam optical laser pick up. 5. 16 program memory. 6. LCD display - back lit green. 7. Shuffle function (random selection). 8. Repeat facility. 9. Intro scan facility. Note: The specification and design are subject to change for improvements without notice. NOTE The equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause interference to radio communications. However, there is no guarantee that interference will not occur in some instances. If this product causes interference to radio or television reception, which can be determined by turning the equipment off and on, try to correct this by one or more of the following measures: Reorient...