Stimmen - 4, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
Inserting batteries into the remote You can control the player using the supplied remote. Insert two size AA (R6) batteries by matching the + and – on the batteries to the diagram inside the battery compartment. Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position. When using the remote, point it at the remote sensor g on the player. Hooking Up the System Overview This section describes how to hook up the CD player to an amplifier. Be sure to turn off the power of each component before making the connections. COMMAND CONTROL A1 MODE CD player To an AC outlet Amplifier To line output (L)To line output (R) To an AC outlet: Signal flow To audio input When to replace batteries With normal use, the batteries should last for about six months. When the remote no longer operates the player, replace all the batteries with new ones. Notes • Do not leave the remote near an extremely hot or humid place. • Do not drop any foreign object into the remote casing, particularly when replacing the batteries. • Do not expose the remote sensor to direct sunlight or lighting apparatuses. Doing so may cause a malfunction. • If you do not use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. What cords will I need? Audio cord (1) (supplied) White White (L) (L) Red Red (R) (R) 4 Getting Started Getting Started Hookups When connecting the audio cord, be sure to match the color-coded cord to the appropriate jacks on the components: Red (right) to Red and White (left) to White. Be sure to make connections firmly to avoid hum and noise. CD player Amplifier INPUT CD L R LINE OUT L R • If you have a Sony receiver (amplifier) equipped with the CONTROL A1 jack Be sure to connect the player to the CD IN jacks on the receiver (amplifier). When making this connection, set the COMMAND MODE of the player to CD1 (see the illustration below). If you further connect the player and the receiver (amplifier) via the CONTROL A1 jacks with the monaural (2P) mini-plug cord (not supplied), you can use the Auto Function feature between these components. For details, refer to the supplementary “S-LinkTM/CONTROLA1 Control System” instructions and the instructions supplied with the receiver (amplifier). When to use the COMMAND MODE selector The COMMAND MODE selector is set to CD1 at the factory for normal use. You can control this player by connecting to a Sony CD Player with the player control function, via the CONTROL A1 jacks. When making this connection, set the COMMAND MODE selectors of each player to the appropriate position according to the connected line input jacks. For details, refer to the instructions supplied with the connected player. When using another Sony CD player together with this player You can make the supplied remote effective only for this player. • When using the player equipped with the COMMAND MODE selector: Set the COMMAND MODE selector of this player to CD1 and that of another player to CD2 or CD3. Then set the CD1/2/3 switch on the remote supplied for each player accordingly. • When using the player not equipped with the COMMAND MODE selector: The command mode of the player without the COMMAND MODE selector is set to CD1. Set the COMMAND MODE selector of this player to CD2, and set the CD1/2/3 switch on the remote to CD2. Connecting the AC power cord Connect the AC power cord to a wall outlet. Note on placement Be sure to place the player on a horizontal place. If the player is slanted, it may cause malfunction or damage the player. COMMAND MODE 1 2 3 CD Getting Started Getting Started Inserting CDs You can insert up to 200 discs into this player. POWER Front cover OPEN JOG POWER Playing position Rotary table Loading position 1 Press POWER to turn on the player. 2 Press OPEN. Front cover 3 Turn the JOG dial until you find the disc slot where you want to insert a disc, while checking the disc number (written beside every five slots and also indicated in the display). Disc number The disc number at the loading position appears in the display.* As you turn the JOG dial, the disc number changes. ALL DISCS CD 1 d SC1 20 Disc number You can arrange your discs into groups and play them within a certain group using the Block Play function. When using this function, you have to insert discs into the slots assigned to one of the eight groups. For details, see “Playing Discs in a Group” on page 15. * If you have already inserted discs, the disc number at the playing position appears. When you turn the JOG dial, the displayed disc number changes to the one at the loading position. 4 Insert a disc with the label side facing right. Notes • Make sure you have inserted the disc into each slot at a right angle to the rotary table. If the disc is not put in straight, it may damage the player or the disc. • Make sure the rotary table comes to a complete stop before inserting or removing discs. With the label side facing ri...