Stimmen - 1, Durchschnittliche Bewertung: 4 ( )

Hersteller: Kenwood Dateigröße: 211.77 kb Dateiname: Unterrichtssprache:

When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 19. Overloading -Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 20. Attachment -Do not use attachments not recommended by the appliance manufacturer as they may cause hazards. 21. Replacement parts -When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock, or other hazards. 22. Safety check - Upon completion of any service or repairs to this appliance, ask the service technician to perform safety checks to determine that the appliance is in proper operating condition. Notes: 1. Item 3 is not required except for grounded or polarized equipment. 2. Item 17 and 18 are not required except for units provided with antenna terminals. 3. Item 17 complies with UL in the U.S.A. SPEED 45 33 CUT Motor puller cover SPEED 45 33 CUT Motor puller cover 6 Parts nomenclature and assembly P-110 (En) Verify that all of the following parts are present before carrying out the assembly procedures. First, set the MM. AMP switch on the bottom according to the type of your amplifier. (Refer to “Connections” below.) Installing the hinges After connections, remove the plas- tic tie that retains the tonearm. Hinge Dust cover Removing the plastic tie Releasing the arm rest lock lever Tonearm plastic tie This until has a built-in RIAA equalizer amplifier, so it can be connected to an amplifier without PHONO (turntable) input jacks. According to the amplifier, set the MM.AMP switch on the bottom cover. MM.AMP OFF ON PHONO L R AUX L R MM.AMP OFF ON MM.AMP OFF ON Rear panel of the amplifier Audio cord White Red Rear panel of the amplifier When the unit is connected to the PHONO (MM) jacks : When the unit is connected to the AUX jacks, etc. : Dust cover AC plug adaptor (Only for some areas) Rubber mat Audio cords AC cord Center spindle Turntable platter SPEED selector Connections EP adaptor Arm elevator Cueing lever Arm rest Tonearm Cartridge CUT key Caution: Do not apply oil or lubrication to the motor, tonearm, or any of the turntable’s mechanisms. Do not plug in the power cord until all connections are completed. 7 7 P-110 (En) Using the stylus cover Before operation, remove the stylus cover in the direction of the arrow After record play, always put on the stylus cover to protect stylus tip. Replacing the stylus Install the new stylus as shown. Remove the existing stylus as shown. O Use an N-69 replacement stylus. O Remove this unit’s power cord from the AC outlet before re- placing the stylus. O One stylus is good for playing an LP record approximately 500 times. Stylus Operating instructions When playing 33 rpm record. When playing 45 rpm record. 2Select 33 or 45. With an EP (single) record EPLP With an LP record EP adaptor 1Placing a record on the platter. SPEED 45 33 CUT SPEED 45 33 CUT SPEED 45 33 O It may happen that tonearm returns automatically to the arm rest before play start. If this occurs, repeat steps (1) and (2) again. O The turntable platter begins rotating when the tonearm is moved over the record. O The tonearm is lowered on the record surface and playback starts. Tonearm (2) Tilt the cueing lever to the front. (1) Pick up and move the tonearm to the position where you wish to begin listening. 4Playing the record. O To resume playback, set the Tilt the cueing lever to the rear. To pause record playback O The tonearm automatically returns to the arm rest when To stop record playback CUT 3Tilt the cueing lever to the rear. O The arm elevator rises. cueing lever to front side. playback is finished. 8 In case of difficulty 8 In case of difficulty P-110 (En) What appears to be a malfunction may not always be serious. If your unit should not perform as expected, consult the table below to see if the problem can be corrected before seeking help from your dealer or service representative. Symptom Cause Remedy No sound from both left and right channels or one channel. O Turntable audio cable are not connected correctly. O Check connections to amplifier. Loud hum, no music. O Poor connection of turntable audio cables. O Make solid connections to amplifier. Howling drowns out music when volume is increased. O Speaker vibration picked up by turntable. O Separate turntable from speakers. Turntable platter does not turn. O Poor AC plug contact. O Turntable belt does not engage with the motor pulley. O Check connection. Make sure AC outlet is active. O Engage the turntable belt with the motor pulley. Poor tracking O Excessive dust on record or stylus. O Stylus tip wear. O Remove dust from stylus or record. O Replace the stylus. (Refer to “Replacing the stylus” on page 7.) Sound is too low or distorted. O ...

Herunterladen

Geben Sie zwei Ziffern: