Stimmen - 3, Durchschnittliche Bewertung: 3.3 ( )

Hersteller: Dell Dateigröße: 2.14 mb Dateiname: Unterrichtssprache:

Obtaining Technical Assistance If you do not understand a procedure in this guide or if the system does not perform as expected, see your Hardware Owner’s Manual. Dell™ Enterprise Training and Certification is available; see for more information. This service may not be offered in all locations. Getting Started With Your System 8 Getting Started With Your System Installation and Configuration CAUTION: Before performing the following procedure, read and follow the safety instructions and important regulatory information in your Product Information Guide. This section describes the steps to set up your system for the first time. Unpack your system and identify each item. Keep all shipping materials in case you need them later. Install the Rails and System in a Rack Once you have read the "Safety Instructions" located in the rack installation documentation for your system, install the rails and the system in the rack. See your rack installation documentation for instructions on installing your system in a rack. Connect the Keyboard, Mouse, and Monitor Connect the keyboard, mouse, and monitor (optional). The connectors on the back of your system have icons indicating which cable to plug into each connector. Be sure to tighten the screws (if any) on the monitor's cable connector. Getting Started With Your System Connect the Power Connect the monitor (optional) and system power, and connect the system’s power cable(s) to the system. If your system has an expansion card with a video output connector, do not connect the monitor to system’s integrated video connector. Instead, connect the monitor cable to the connector on the expansion card. Plug the other end of the cable into a grounded electrical outlet or a separate power source such as an uninterrupted power supply (UPS) or a power distribution unit (PDU). Getting Started With Your System Install the Power Cord Retention Bracket Attach the power cord retention bracket on the right bend of the power supply handle. Bend the system power cable into a loop as shown in the illustration and attach to the bracket’s cable clasp. Repeat the procedure for the second power supply. Plug the other end of the power cables into a grounded electrical outlet or a separate power source such as an uninterrupted power supply (UPS) or a power distribution unit (PDU). Getting Started With Your System 12 Getting Started With Your System Turn on the System Turn on the system and monitor (optional). Press the power button on the system and the monitor. The power indicators should light. Adjust the monitor's controls until the displayed image is satisfactory. Install the Bezel Install the bezel (optional). Complete the 0perating System Setup If you purchased a preinstalled operating system, see the operating system documentation that ships with your system. To install an operating system for the first time, see the Quick Installation Guide. Be sure the operating system is installed before installing hardware or software not purchased with the system. Technical Specifications Processor Processor type One or two Dual-Core Intel Xeon Processors 5000 Sequence. Expansion Bus Bus type PCI-X, PCIe Expansion slots Center riser: PCIe one half-height x8 lane 3.3-V (slot 1) Left riser PCI-X option: two full-height, full-length 3.3-V, 64-bit, 133-MHz (slots 2 and 3) OR PCIe option: one full-height x8 lane 3.3-V (slot 2) and one full-height x4 lane 3.3-V (slot 3) Memory Architecture 533 or 667 (when available) MHz Fully Buffered DIMMs (FBD) Memory module sockets eight 240-pin Memory module capacities 256 MB, 512 MB, 1 GB, 2 GB, or 4 GB Minimum RAM 512 MB (two 256-MB modules) Maximum RAM 32 GB Getting Started With Your System Drives Hard drives up to six 3.5-inch, internal hotpluggable SAS or SATA hard drives without optional media bay, OR up to four 3.5-inch internal hotpluggable SAS or SATA hard drives with optional media bay Diskette drive one optional 3.5-inch, 1.44-MB external optional USB 3.5-inch, 1.44-MB Optical drive one optional slimline IDE CD, DVD, or combination CD-RW/DVD NOTE: DVD devices are data only. external optional USB CD Tape drive one optional internal half height tape backup device Flash drive external optional USB Connectors Back NIC Two RJ-45 (for integrated 1-GB NICs) Serial 9-pin, DTE, 16550-compatible USB Two 4-pin, USB 2.0-compliant Video 15-pin VGA Front Video 15-pin VGA USB Two 4-pin, USB 2.0-compliant Video Video type ATI ES1000 video controller; VGA connectors Video memory 16 MB of DDR SDRAM Getting Started With Your System Power AC power supply (per power supply) Wattage 750 W Voltage 85–264 VAC, autoranging, 47–63 Hz Heat dissipation 2697 BTU/hr maximum Maximum inrush current Under typical line conditions and over the entire system ambient operating range, the inrush current may reach 55 A per power supply for 10 ms or less. Batteries System battery CR 2032 3.0-V lithium ion coin cell RAID battery (optional) 4.1-V lithium ion Physical Rack Heig...

Herunterladen

Geben Sie zwei Ziffern: