Stimmen - 4, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
Consult a qualified technician for instructions. • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started • Remove 2 transit screws located on top of the unit. • Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve. • Install mounting sleeve into opening, bending tabs to secure. • Connect wiring harness and antenna. Consult a qualified technician if you are unsure. • Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately). • Test for correct operation and slide into mounting sleeve to secure. • Snap trim ring into place. KEYSHEX BOLTMOUNTING SLEEVEPLAIN WASHERHEX NUTMOUNTING STRAP TYPICAL MOUNTING METHOD 3 XD1222 INSTALLATION Wiring Diagram Rear Preamp OutputConnect to amplifier RCA inputAntenna ConnectorRCA Cable(sold separately) AMPBLUEBLACKREDYELLOWRemote Turn-OnConnect to amplifier or powerantenna. Insulate wire if not used. GroundConnect to vehiclechassis ground. AccessoryConnect to ignition circuit or switched 12 volt source. MemoryConnect to battery circuit or constant 12 volt source. Right FrontGray/Black (-) Gray (+) Left FrontWhite/Black (-) White (+) Right RearViolet/Black (-) Violet (+) Left RearGreen/Black (-) Green (+) 5 AMPAGC Fuse FUSE When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The XD1222 uses one 5 amp AGC fuse located in-line. * Caution - Do not attach any speaker leads to ground as severe damage will occur. XD1222 OPERATION Control Locations 11 5 6 4 9 8 3 2 12 13 7 10 1 19 17 16 18 14 15 20 Tune/Track Down Eject Tune/Track Up EQ/Stereo/Mono Auxiliary Input Audio/Loudness USB Charge AS/PS Band Display Release Mode Power Rotary Encoder Preset 4/Play/Pause Preset 1/Repeat Preset 5 Preset 2/Random Preset 3/Intro Preset 6 11 1 12 2 13 3 4 14 5 15 6 16 7 17 8 18 9 19 20 10 The XD1222 has an easy-to-use interface that provides a rewarding experience, as well as support for your favorite tunes. Audio CD-R and CD-RW disc playback ensures compatibility with your music collection, and the RCA preamp output provides the right connections to expand your system. From its front panel auxiliary input for connecting your MP3 player, to the detachable face for security assurance, this head unit has you covered. XD1222 OPERATION General Operation Press RELEASE and pull away from the left side to remove. To re-install, insert right side of faceplate first then push left side to secure. Remove trim ring and install supplied #1 x 7/32” Phillips head screw through left side of mounting frame into faceplate. Press PWR to turn the unit on. Inserting a CD will turn the unit on automatically. Press PWR to turn the unit off. Press MODE to select between AM/FM, CD or auxiliary input. Modes of operation are indicated in the display. Press and hold LOUD for 2 seconds to activate and deactivate the loud feature. Activating this feature will enhance the bass and treble frequencies when listening to music at low volumes. Insert a 3.5mm connector in the front panel AUX port. Connect the other end of the 3.5mm connector to the headphone output of an audio device, MP3 player, etc. Press MODE to select AUX mode. Adjust volume using the rotary encoder (00-46). Press DISP to display the clock. The radio frequency (tuner mode) and CD track/elapsed time (CD player mode) will be shown by default. Press DISP to display the clock, then release. Press and hold DISP for 2 seconds, the clock will begin to flash. Press TRACK nn to adjust the hours and TRACK ll to adjust the minutes. Clock settings will be saved after 5 seconds. The clock will display 12-hour AM/PM time in USA frequency spacing mode (PM 10:00). In European frequency spacing mode, the clock will display 24-hour time (22:00). Press and hold for more than 2 seconds to RESET the unit upon initial installation. The RESET button is located behind the faceplate. Faceplate Removal Semi-permanent Faceplate Installation Power On/Off Mode Loud Auxiliary Input Volume Display Set the Clock 12/24-hour Clock Reset XD1222 OPERATION General Operation USB Charging Port Select Audio Bass Treble Balance Fader Preset EQ Curves Insert the USB connector of a battery powered USB device into the USB charging port on the front panel, which provides 5 volts DC and 1.0 amps. The USB device will immediately begin charging. Note: The USB charging port may not be compatible with every device due to differences in power requirements. Note: This USB port provides power only, and will not playback music from a USB device. Press AUDIO to select between Volume (default), Bass, Treble, Balance & Fader. Press AUDIO until BA appears Rotate the rotary encoder left/right to adjust (-6 minimum / 6 maximum) Press AUDIO until TR appears Rotate the rotary encoder left/right to adjust (-6 minimum / 6 maximum) Press AUDIO ...