Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
6 ~ 10 Español.................... ....................11 - 15 Français................... ...........;.......16- 20 Italiano..................... ...................21 - 25 NOTES ON SAFE AND EFFICIENT OPERATION: ■ Do not use this CD Player where the temperatures go below 41 °F / 5°C or exceed 95°F / 35°C. ■ Place the unit in a clean and dry location. ■ Do not place the unit in an unstable location. ■ When disconnecting the power cord from an AC outlet, always grasp it by the plug. Never pull the power cord. ■ Never open the cabinet. If the unit is not functioning correctly, call the Gemini Service Center at (908) 969-9000. ■ Do not use chemical solvents to clean the unit. ■ Keep the laser pickup clean by keeping the drawer closed. ■ Keep this manual in a safe place for future reference. SAFETY CERTIFICATIONS: Laser Diode Properties Material: Ga - AI - As Wavelength: 755 - 815 nm (25° C) Laser Output: Continuous Wave max 0.5mW ^ CAUTION To prevent electric shock, do not remove the cover or the bottom screws. There are no user serviceable parts inside. Please refer servicing to a qualified technician. Page 1 LINE VOLTAGE SELECTION: Model CD-4700 PRO II is a dual voltage unit. It will operate at 115 or 220 volts. The unit is preset at the factory to 115 volts. To set the proper voltage follow these steps: 1. Place the head of a screw driver in the center of the VOLTAGE SELECTOR SLIDE SWITCH ( 15 ) found on the rear panel. 2. Slide the switch up for 115 volts or push the switch down for 220 volts. 3. Do not force or twist the switch. Excessive force may cause damage. If the switch does not move smoothly, contact a qualified technician. © 0 © AMS:RISQUE PE CHOC ëlECTttlQUE-NE PAS OUVRIR CONNECTIONS: A typical connection with a mixer is illustrated above. Please use it as a reference. 1. Plug one end of a set of RCA connectors into the LINE OUTPUT JACKS (16 ). 2. Plug the other end of the RCA connectors into any available line level input jacks on your mixer. If you are playing the CD-4700 PRO II through a receiver, you can plug the RCA connectors into the CD input jacks on your receiver. If there is no CD input, use AUX or any other line level (not phono). FUNCTION DESCRIPTIONS: © © © © @ © <30' MIXER LINE INPUT Page 2 1. POWER SWITCH: After making sure that the VOLTAGE SELECTOR SLIDE SWITCH (15), found on the rear panel, is properly set, plug the unit in and press the POWER SWITCH (1 ). The unit will turn on. Pushing the POWER SWITCH (1 ) a second time will turn the unit off. 2. DISC TRAY: The DISC TRAY ( 2 ) is where the CD is held during loading, unloading and playback. Pressing the disc tray OPEN/CLOSE BUTTON (3), will open or close the tray. The DISC TRAY ( 2 ) holds both 12 cm and 8 cm CDs. NOTE: If the CD-4700 PRO II is in the play mode, the tray will not open. 3. OPEN/CLOSE BUTTON: Press the OPEN/CLOSE BUTTON ( 3 ) to load or remove a CD from the DISC TRAY ( 2 ). 4. DISPLAY: The DISPLAY ( 4 ) shows the track number, play mode, pause mode, and 3 different time displays. These time displays are time elapsed on the track, time remaining on the disc and time remaining on the track. 5. PLAY/PAUSE: Each press of the PLAY/PAUSE BUTTON ( 5 ) causes the operation to change from play to pause or from pause back to play. See the CUE INSTRUCTIONS section for more information. 6. TRACK SKIP: The TRACK SKIP BUTTONS ( 6 ) let you select the track to play. 7. SEARCH BUTTONS: The SEARCH BUTTONS ( 7 ) are used to accurately position the disc at the point where you wish the track to start playing. This position on the track is memorized as the cue point. Each push of the SEARCH BUTTONS (7) will put the CD unit in the pause mode and will move the memorized cue point 1 frame (1/75th second). See the CUE INSTRUCTIONS section for more information. 8. SEARCH DIAL: Use the SEARCH DIAL (8) to select the scanning direction and speed. Turning the dial in the clockwise direction will scan forward and counter clockwise will scan in reverse. The scanning speed increases as the dial is turned further. The SEARCH DIAL (8) will not change the cue point and will not bring the unit to the pause mode. 9. STOP: The STOP BUTTON ( 9 ) will end the playing of the CD. 10. TIME: The TIME BUTTON (10) switches the time display between the three available choices listed under #4 (DISPLAY). 11. CUE: With the unit in the play mode (play/pause LED glows green), and after using the SEARCH BUTTONS ( 7 ) to memorize the cue point, pressing the CUE BUTTON (11 ) will cause the CD player to enter the pause mode (play/pause LED blinks green) at the memorized cue point ( the cue LED glows yellow ). If the cue point was not memorized, the unit will return to the beginning of the track. Holding down the cue button changes the cue function to preview (allowing you to hear the music play at whatever tempo you adjusted to by holding the cue button down). Releasing the cue button returns you to the preset cue poin...