Login:
Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Audiovox, modell CDC-825

Hersteller: Audiovox
Dateigröße: 168.4 kb
Dateiname: a99d2b6d-9d3f-412a-bbfe-2272bdcba4b7.pdf

Unterrichtssprache:en

Das Dokument wird geladen, bitte warten
Das Dokument wird geladen, bitte warten

Anleitung Zusammenfassung


When a desired disc is reached, press the Scan button again and play of that disc will continue ("SCAN" and "DISC" will disappear from the display). Disc Scan mode will also be cancelled by activating any other function (Repeat, Shuffle, Disc Select, Track Skip, or Track Search). blREMOTE SENSOR The sensor for the infrared signal from the optional wireless remote control is located behind this lens. For optimal operation of the remote control, keep the lens clean and do not allow objects to block it. bmRESETBUTTON A reset button is located on the front panel of the remote control which must be activated with a pen or other thin object as it is recessed to prevent accidental engagement. The reset circuitry is provided to protect the unit’s microprocessor and laser pick-up system and should only be activated under the following circumstances: 1. Initial installation after all wiring is completed (this must be done). 2. If abnormal disc operation is encountered, the reset button may be pressed to clear the system and return to normal operation. IMPORTANT: Use of the Reset button on the CD Changer will cause the CD magazine to be automatically ejected. Make certain changer door is fully opened prior to using Reset. CAUTION: When the CD magazine is ejected by the use of the Reset button, whichever disc was in play prior to depressing Reset may be left in the play position in the changer. It is critical that before re-inserting the CD magazine, you must REMOVE ALL DISCS from it. After you have inserted the empty CD magazine, press the "EJECT" button on the changer and the "in play" disc will be loaded into the empty magazine. You may then remove the magazine and re-load as many discs as desired. WARNING: Avoid use of Reset buttons after initial use unless you have a definite abnormal disc operation. Use the EJECT button on the changer to remove the CD magazine for normal operation. ERROR SIGNS: If a problem should develop while operating the CD changer, the following error signs may be displayed on the LCD panel: E-01: Indicates abnormal disc change function. Contact the place of purchase for further service advise. E-30: Indicates excessive temperature conditions. The error sign will go off and play will resume when the changer temperature returns to normal range -- --: Magazine is not loaded in the changer. 0-00: No discs are loaded in the magazine. 1---: No disc is loaded in magazine slot #1. (2----indication for slot #2, etc.) SPECIFICATIONS: Changer: Frequency Response: 5 -20,000 Hz. ±1 dB Distortion: 0.008% @ 1 kHz. Dynamic Range: 95 dB Signal-to-Noise Ratio: 95 dB Channel Separation: 80 dB @ 1 kHz. Wow & Flutter: below measurable limits FM Modulator: Output Frequency: 88.7/89.1 MHz. (switchable) General: Dimensions: Changer: 11-1/2"W x 3-5/8"H x 7-1/2"D 291 mm x 92 mm x 190 mm Control Unit: 4-3/4"W x 1-5/8"H x 5/8"D 120 mmx40mmx17mm Operating Voltage: 12 volts DC, negative ground WIRELESS REMOTE CONTROL The CDC-10R Wireless Remote Control (optional) is capable of operating all functions of the wired control unit. Each button on the remote control functions in the same way as the comparable button on the wired control unit. For optimal operation of the remote control, always aim it toward the Remote Sensor bl on the control unit. PLAY / PAUSE ( / ) 9 See Wired Control Unit 2 POWER OFF SWITCH (OFF) See Wired Control Unit 3 DISC SELECT (-+) 21 See Wired Control Unit 4 TRACK SKIP ( ) 45 3 See Wired Control Unit 5 TRACK SEARCH ( 8 6) See Wired Control Unit 7 7 6 TRACK / DISC SHUFFLE (SHF) See Wired Control Unit 7 TRACK / DISC REPEAT (RPT) See Wired Control Unit 8 BATTERY COMPARTMENT TRACK / DISC (SCN) See Wired Control Unit 9 9 INFRARED SENDER The wireless signal from the remote control is sent from this lens. For optimal range and performance of the remote control, always aim the Sender at the Remote Sensor blon the wired control unit. Do not let your finger interfere with the signal and make sure the lens does not become blocked by dirt, dust, etc. If necessary, clean the lens with a soft dry cloth or cotton swab. NOTES ON REMOTE CONTROL USE: . The remote control operates on a 3 volt lithium battery (type CR-2025). Install the battery into the compartment at the bottom of the remote control, making sure to observe correct polarity (match .+“ side of battery to .+“ indication on compartment). . If remote control fails to operate, always check battery condition and replace if necessary before servicing the unit. . Dispose of batteries properly. Do not heat, disassemble, or throw batteries into a fire. . Keep the remote control away from areas where it may be exposed to heat, moisture or sunlight. TROUBLESHOOTING An error made in operation or during installation of this product may be mistaken for a system malfunction. Please perform the checks described below before contacting your dealer or service facility. Symptom Possible Cause Remedy No power Blown fuse Check fuses in vehicle fuse box and changer system. R...

Dieses Handbuch ist für folgende Modelle:
CD-Player - CDC-10R (168.4 kb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien