Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
DO NOT REMOVE COVER. PILOT LAMPS SOLDERED IN PLACE. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. IMPORTANT NOTES CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (ON BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash and arrowhead within the triangle is a warning sign alerting you of "dangerous voltage" inside the product. instructions accompanying the product. a warning sign alerting you of important The exclamation point within the triangle is *Avoid installing the unit in locations described below: - Places exposed to direct sunlight or close to heat radiating appliances such as electric heaters - On top of other stereo equipment that radiates too much heat - Places lacking ventilation or dusty places - Humid or moist places *Read Owner’s Manual before operating *Be sure all connections are properly made before turning power on. IDENTIFICATION OF CONTROLS / CONNECTIONS 1) Tuning Up / Track Up / Seek / Minute Set Button 2) Tuning Down / Track Down / Seek / Hour Set Button 3) Mute / AS/PS / Loud Buttons 4) Time Set Button 5) Display Window 6) Alarm Set / Alarm On/Off Buttons 7) Button Reset 8) Preset / Repeat Button 9) Preset / Shuffle Button 10) Preset / Scan Button 11) Preset Buttons 12) CD Player 13) CD Eject Button 14) Speaker Selector 15) 1/8” Auxiliary Input Jack 16) Stereo Headphone Jack 17) Audio Adjust Button 18) Power Switch with Volume Control 19) Source Selectors 20) Car Antenna 21) FM Antenna Terminals 22) RCA Auxiliary Input Terminals 23) Harness 1 INSTALLATION AND HOOK UP 1) Cut mounting hole in desired location using mounting hole diagram (right) 2) Route power, speaker, and antenna cables through hole, and connect to unit as shown in hook up diagram below. 3) After making sure connections are correct, test unit operation as described in the operation section (Do not mount until AM antenna trimmer adjustment has been made. WIRING COLOR CODE FOR AWM-930 COLOR ORANGE/WHITE GREEN/WHITE BLACK/WHITE WHITE VIOLET BLUE GREEN RED VIOLET/BLACK YELLOW GREEN/BLACK FUNCTION +12VDC IGNITION POWER +12VDC BATTERY POWER TO CHASSIS GROUND LEFT (A) SPEAKER (+) LEFT (A) SPEAKER (-) RIGHT (A) SPEAKER (+) RIGHT (A) SPEAKER (-) LEFT (B) SPEAKER (+) LEFT (B) SPEAKER (-) RIGHT (B) SPEAKER (+) RIGHT (B) SPEAKER (-) NOTES: - Speakers must have a minimum of four W impedance each. -Either antenna may be used. Both do not have to be hooked up at the same time. - Do not operate this unit with only one speaker hooked up. If a speaker fails, replace it before operating this unit. NOTE: Always be sure when running cables to avoid sharp edges, extreme heat sources, and any other potential hazards. 2 OPERATING INSTRUCTIONS NOTE: Number in parenthesis (#) corresponds with “Identification of Controls / Connections” on page 1 of this manual. LIQUID CRYSTAL DISPLAY PANEL The liquid crystal display (LCD) panel displays the frequency, time, and activated functions. Note: It is a characteristic of LCD panels that if subjected to cold temperatures for an extended period of time, they will take longer to illuminate than under normal conditions. In addition, the visibility on the numbers of the LCD may slightly decrease. The LCD read out will return to normal when the temperature increases to a normal range. TUNER 1) Turn power on by pushing the Power Switch Control Button (18). 2) Use the Source Selectors (19), select the AM /FM button. 3) Use the Speaker Selector Switch (14) to choose between speaker output, headphones, or both. 4) Use Tuning Up (1) or Down (2) buttons to select the station manually. Also, the Station Preset buttons can select stations (this will be discussed later in the manual). Push either of the Seek buttons (1 or 2) to tune to the next higher or lower active station. 5) Adjust Volume Control (18) to suit taste. CD PLAYER 1) Turn power on by pushing the Power Switch / Volume Control button (18). 2) Use the Source Selectors (19), to select the CD button. 3) Use the Speaker Selector Switch (14) to choose between speaker output, headphones, or both. 4) Press the CD Eject button (13) to eject any CD’s that may already be in the player. 5) Insert an audio CD into the CD player (12). 6) Press the CD Play / Pause button (the same as the CD Source Select button). 7) You may change tracks by using the Track Up or Track Down buttons (1 or 2). 8) To eject the CD, press the CD Eject button (13). 3 CD CONTROL BUTTONS The RPT button (8) repeats the current track The SHF button (9) randomly shuffles the tracks. The SCN button (10) scans the first 5 seconds of each track. Note: Power can be turned on by pushing any button on the front of the AWM930. AUXILIARY INPUT 1) Push Power Switch (18) “on”. 2) Using the Sour...
Dieses Handbuch ist für folgende Modelle:CD-Player - AWM930W (246.23 kb)