Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Fotos und technische Daten Alpine CDA-7873R |
Anleitung Zusammenfassung
Hold the disc so you will not leave fingerprints on the surface. Do not affix tape, paper, or gummed labels to the disc. Do not write on the disc. CORRECT INCORRECT CORRECT Disc Cleaning Fingerprints, dust, or soil on the surface of the disc could cause the CD player to skip. For routine cleaning, wipe the playing surface with a clean, soft cloth from the centre of the disc to the outer edge. If the surface is heavily soiled, dampen a clean, soft cloth in a solution of mild neutral detergent before cleaning the disc. Disc Accessories There are various accessories available on the market for protecting the disc surface and improving sound quality. However, most of them will influence the thickness and/or diameter of the disc. Using such accessories can cause the disc to be out of standard specifications and may create operational problems. We recommend not using these accessories on discs played in Alpine CD players. Transparent Sheet Disc Stabilizer 3-EN Tape Slack Check and make sure any slack in the tape is taken up before inserting the tape into the unit. A loose tape can get caught in the mechanism and cause damage to the unit and the tape itself. Tighten the tape by inserting a pencil or a similar instrument into the spindle hole and turn until all the slack has been taken up. Excessively Thin Tape C-120 type cassette tapes are not recommended for use in automobile tape players. Precision Tape Mechanism Prevent any foreign objects from entering the cassette opening as the precision mechanism and tape head may be damaged. Never play dirty or dusty tapes – they can damage the tape head. Tape Head Cleaning Periodic cleaning (approximately every 20 hours of use) of the tape head with a wet type head-cleaning cassette tape (available at audio stores) is necessary for best performance. Fuse Replacement When replacing the fuse(s), the replacement must be of the same amperage as shown on the fuse holder. If the fuse blows more than once, carefully check all electrical connections for shorted circuitry. Also have your vehicle's voltage regulator checked. 4-EN Basic POWER RESET Basic Operation Detaching the Front Panel 1 Press and hold the POWER button at least 3 seconds to turn off the power. 2 Press the (Release) button at left side until the front panel pops out. 3 Grasp the left side of the front panel and pull it out. NOTES • The front panel may become hot in normal usage (especially the connector terminals on the back of the front panel), this is not malfunction. • To protect the front panel, place it in the supplied carrying case. Attaching the Front Panel 1 First, insert the right side of the front panel into the main unit. Align the groove on the front panel with the projections on the main unit. 2 Push the left side of the front panel until it locks firmly into the main unit. 211 • Controlable with Remote Control (CDA-7873R only) This unit can be controlled with an optional Alpine remote control. For details, consult your Alpine dealer. Point the optional remote control transmitter at the remote control sensor. Remote control sensor • Connectable to Remote Control Interface Box You can operate this unit from the vehicle's control unit when an Alpine Remote Control Interface Box (optional) is connected. For details, contact your Alpine dealer. Initial System Start-Up Immediately after installing or applying power to the unit, it should be initialized. Press the RESET switch with a ballpoint pen or any other pointed object. NOTE Before attaching the front panel, make sure that there is no dirt or dust on the connector terminals and no foreign object between the front panel and the main unit. 5-EN Basic POWER TUNE MODE/BBE g DN f UP SETUP ANGLE 89 c Basic Operation About Demonstration This unit is equipped a Demonstration function. Soon after resetting the unit or after turning the unit on the first time, the demonstration starts automatically. To cancel the demonstration, refer to “Demonstration” on page 10. Turning Power On and Off 1 Press the POWER button to turn on the unit. NOTE The unit can be turned on by pressing any other button except the eject c button. The volume level gradually increases to the previous level you were listening to before the unit was turned off. Press and hold the POWER button for at least 3 seconds to turn off the unit. NOTE The very first time the power is turned on, the volume will start from level 12, the BBE will be on in the tuner mode. Display Angle Adjustment Movable display The movable display may be adjusted to 3 different angles depending upon user preference. 1 Press the ANGLE 89 button to adjust the angle of the movable display. NOTES • The display will close a half minute after the ignition key is turned to the OFF position. • The adjusted angle of the display is stored in memory. There is no need to re-adjust the angle when the power is turned back on. CAUTION Keep hands (or any other object) away from the display while it is opening or closing to avoid damage ...
Dieses Handbuch ist für folgende Modelle:CD-Player - CDA-7876RB (455.16 kb)