Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Pressing the CUE BUTTON (27) will stop playback and return the disc in cue mode, pressing the RELOOP/BOP BUTTON (30) will return the disc to cue point without music interruption and continue playback from that point. Figure 18 2) The JOG WHEEL (19) may be used to set a cue point by frame. While a disc is in pause or cue mode, use the JOG WHEEL (19) to scroll through a track to find your desired starting point. Once you have found your desired cue point press the PLAY BUTTON (29) to enter this point in to the unit's memory. At this point pressing either the CUE BUTTON (27) or the RELOOP/BOP BUTTON (30) will return you to this exact point. Figure 19 Storing A Cue Point: Once you have set a cue point by one of the two means as detailed above, you may store this point in any one of the CUE MEMORY BUTTONS (6). Once a cue point is stored in to memory it may be recalled at any time by pressing the cue button it was stored into. A cue point may even be recall if the disc has been remove or power had been disconnected. To Store a cue point: 1) Create a cue point, press the CUE MEMORY BUTTON (6), as in Figure 20. The yellow Cue Memory LED will glow. This indicates a cue point is ready to be stored in to memory. Figure 20 American Audio® • DIGI-PRO™ INSTRUCTION MANUAL • PAGE 20 BASIC OPERATIONS (CONT.) BASIC OPERATIONS (CONT.) 2) At this point pressing any one of the four CUE BUTTONS (6) will store your cue point into memory (Figure 21), and the yellow Cue Memory LED will shut off. 3) Repeat steps one and two to store up to four Cue Points. Once all your four cue points have been stored you may access them at any time. 4) During playback the cue points will instantly start without any music interruption. During play or pause mode accessing a stored cue point will cue to that point in pause mode. Figure 21 14. CREATING AND PLAYING A SEAMLESS LOOP A seamless loop is a sound loop that plays continuously without sound interruption. You can use this loop to create dramatic effect in your mixing. This loop has no time limit and you could actually loop the entire length of disc. You create a seamless loop between two continuous points of a disc. The following steps illustrate the procedures for creating a seamless loop: 1) Press the PLAY/PAUSE BUTTON (29) to activate playback mode. 2) Press the IN REAL-TIME CUE BUTTON (26). This will set a loops starting point. The IN REAL-TIME CUE BUTTON (26) LED will briefly indicating a starting point has been set. Figure 22 Figure 23 American Audio® • DIGI-PRO™ INSTRUCTION MANUAL • PAGE 21 BASIC OPERATIONS (CONT.) BASIC OPERATIONS (CONT.) 3) Press the OUT/EXIT BUTTON (28) to set the ending point for your SEAMLESS LOOP (Figure 13). The IN REAL-TIME CUE BUTTON (26) and OUT/EXIT BUTTON (28) LEDs will begin to flash indicating SEAMLESS LOOP mode has been activated. LOOP INDICATORS - During a seamless loop, the LOOP (65) and RELOOP (64) INDICATORS will light in the LCD (14) indication a loop is active. Figure 24 EXITING A LOOP - To exit a SEAMLESS LOOP, press the OUT/EXIT BUTTON (28). The IN REAL-TIME CUE BUTTON (26) and OUT/EXIT BUTTON (28) LEDs will remain on, but will stop flashing. Music playback will resume normal play (Figure 25). The IN REAL-TIME CUE BUTTON (26) and OUT/EXIT BUTTON (28) LEDs will remain on to remind you that a loop is stored in memory. Figure 25 REPLAY LOOP - The RELOOP (30) function allows you to return to your stored loop at any time. The IN REAL-TIME CUE BUTTON (26) and OUT/EXIT BUTTON (28) LEDs will indicate a loop is stored in memory, and may be played at any time. To replay the loop, press the RELOOP/BOP BUTTON (30). The IN REAL-TIME CUE BUTTON (26) and OUT/EXIT BUTTON (28) LEDs will again begin to flash indicating SEAMLESS LOOP mode has been activated (Figure 26) and your stored loop will immediately begin to play. Figure 26 15. EDITING A LOOP: Please note only the ending point of a loop may be edited, a loop may be made shorter or longer. Before you can edit your seamless loop you obviously must first have created a seamless loop to edit. If you haven’t created a SEAMLESS LOOP, follow the instructions in step 10. If a SEAMLESS LOOP has already been created, press the RELOOP/BOP BUTTON (30) to activate your SEAMLESS LOOP (Figure 26), if it is not already playing. To edit a loop’s ending point: 1) Press the OUT/EXIT BUTTON (28) to return to normal play from the loops cue point (Figure 25). This will disengage the SEAMLESS LOOP and allows you to edit the loops ending point. 2) Press the OUT/EXIT BUTTON (28) again when you reach your new ending point (Figure 25). -FOR A SHORTER LOOP: Press the OUT/EXIT BUTTON (28) at sooner point in the track (Figure 25). -FOR LONGER LOOP: Press the OUT/EXIT BUTTON (28) at later point in the track (Figure 25). American Audio® • DIGI-PRO™ INSTRUCTION MANUAL • PAGE 22 BASIC OPERATIONS (CONT.) American Audio® • DIGI-PRO™ INSTRUCTION MANUAL • PAGE 23 1) Be sure a disc is inserted in the drive and press the PRG/HOLD FX (13). Pressing th...