Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
After tuning into a station, the search stops. To stop the Auto Search manually, press 4+ DOWN or UP. The Auto Search may not stop at stations with very weak signals. When an FM stereo broadcast contains noise Press MONO TUNER on the remote control so that “MONO appears on the display. Noise is reduced, although reception is monaural. To restore stereo reception, repeat the above so that “MONO” disappears. To change the AM tuning interval The default setting of the AM tuning interval is 10 kHz/step. If you use this unit in an area where the frequency allocation system is 9 kHz/step, change the tuning interval. Press POWER while pressing b. To reset the interval, repeat this procedure. When the AM tuning interval is changed, all preset stations are cleared. The preset stations have to be set again. ‘—_ ... ......_ du The unit can store a total of 32 preset stations. When a station is stored, a preset number is assigned to the station. Use the preset number to tune in to a preset station directly. 1 Press TUNER BAND to select a band, and press < DOWN or > UP to select a station. 2 Press 1I SET to store the station. A preset number beginning from 1 in consecutive order for each band is assigned to the station. Preset number 3 Repeat steps 1 and 2. The next station will not be stored if a total of 32 preset stations for all the bands have already been stored. m “FULL” is displayed if you attempt to store more than 32 preset stations. Use the remote control to select the preset number directly. 1 Press TUNER BAND to select a band. 2 Press numbered buttons O-9 and +10 to select a preset number. Example: To select preset number 20, press +10, +10 and O. To select preset number 15, press +10 and 5. Selecting a preset number on the main unit Press TUNER BAND to select a band. Then, press ~ PRESET repeatedly or turn MULTI JOG. Each time a PRESET is pressed, the next ascending number is selected. To clear a preset station Select the preset number of the station to be cleared. Then, press q CLEAR, and press II SET within 4 seconds. The preset numbers of all other stations in the band with higher numbers are also decreased by one. 10 ENGLISH MULTI JOG APUSH EJECT Deck 2 This unit is designed for optimal playback of Type I (normal) tapes. 1 Press TAPE and press A PUSH EJECT to open the cassette holder. A PUSH EJECT Insert a tape with the exposed side down. Push the cassette holder to close. 2 Press *to start play. Only the side facing out from the unit can be played back. Selected deck number Tape counter To select a playing deck When tapes are loaded in both decks, press TAPE first to select a deck. The selected deck number is displayed. To stop play, press n . To pause play (deck 2 only), press 11. To resume play, press again. To fast forward or rewind, press 4+ or -. Then press . to stop the tape. To start play when the power is off (Direct Play Function) Press TAPE. The power is turned on and play of the inserted tape begins. To set the tape counter to 0000 Press n CLEAR in stop mode. The counter is also set to 0000 when the cassette holder is opened. When tapes are loaded in both decks After playback on deck 1 finishes, the tape in the deck 2 will start to play without interruption and will stop at the end of the tape. (Continuous play) m Type II (High position) tapes can also be played back in this unit. When playing back a Type II tape, turn MULTI JOG to display “SOFT” in the display. This will set the optimum playback sound for Type II tapes. However, “SOFT playback will be canceled if any graphic equalizer is selected (page 9), the unit is switched to a different audio source, the cassette holder is open, or when the power is turned off. ENGUSH 1 I PLAYING DISCS Load discs. To Dlav all discs in the disc compartment, press -. Play begins with the disc on tray 1. Press CD, then press A OPEN/CLOSE to open the disc compartment. Load disc(s) with the label side “ up. To plav one or two discs, place the discs on tray 1 and 2. To day three discs, press DISC CHANGE to rotate the trays after placing two discs. Place the third disc on tray 3. Close the disc compartment by pressing A OPEN/CLOSE. DISC C’HANGE Tray number of the disc to be played Total number of tracks Total playing time Number of track being played Elapsed playing time To Dlav one disc only, press DISC DIRECT PLAY 1-3. The selected disc is played once. To stop play, press n . To pause play, press 11. To resume play, press again. To search for a particular point during playback, keep ~ or -pressed and release it at the desired point. To skip to the beginning of a track during playback, press < or -repeatedly or turn MULTI JOG. To remove discs, press 4 OPEN/CLOSE. To start play when the power is off (Direct Play Function) Press CD. The power is turned on and play of the loaded disc(s) begins. When A OPEN/CLOSE is pressed, the power is also turned on and the disc compartment is opened. To check the remaining time During play, press CD EDIT/CHECK on the remote ...