Stimmen - 5, Durchschnittliche Bewertung: 3.6
(
)
)
|
Fotos und technische Daten Clarion DB415 |
Anleitung Zusammenfassung
*If the FLIP DOWN PANEL does not open fully, gently open it with your hand. DCP Release button 1 3. Pull the DCP toward you and remove it. DCP 4. Close the HOLD FLAP. HOLD FLAP CAUTION Be sure to close the HOLD FLAP for safety when removing the DCP. Attaching the DCP 1. Insert the right side of the DCP into the main unit. 2. Insert the left side of the DCP into the main unit. 2. DCP 1. CAUTION • The DCP can easily be damaged by shocks. After removing it, be careful not to drop it or subject it to strong shocks. • If the FLIP DOWN PANEL is kept open, the DCP may drop due to vibration of the car. This results in damage to the DCP. So close the FLIP DOWN PANEL or remove the DCP to store into the case. • The connector connecting the unit and the DCP is an extremely important part. Be careful not to damage it by pressing on it with fingernails, screwdrivers, etc. Note: • If the DCP is dirty, wipe off the dirt with a soft, dry cloth only. E glis DB415 1. Turn the remote control unit over, then slide the rear cover in the direction of the arrow. 2. Insert the AA (SUM-3, IECR-6/1.5V) batteries that came with the remote control unit facing in the directions shown in the figure, then close the rear cover. Notes: Using batteries improperly can cause them to explode. Take note of the following points: • When replacing batteries, replace both batteries with new ones. • Do not short-circuit, disassemble or heat batteries. • Do not dispose of batteries into fire or flames. • Dispose of spent batteries properly. 8 DB415 English Rear side AA (SUM-3, IECR-6/1.5V) Batteries Rear cover 7. REMOTE CONTROL & ( . . ° ¤ A ) * . ¦ Receiver for remote control unit Operating range: 30° in all directions Signal transmitter Remote Control Unit Inserting the Batteries If you buy the RCB-130, sold separately, you can enjoy the use of the remote control function. Functions of Remote Control Unit Buttons Mode Button Radio CD FUNC & Turns power on and off. When pressed and held for 1 second: Turns power off. Switches between radio and CD. BAND DISC UP PROG TOP * Switches reception band. Plays the first track. Top play. VOLUME ( Increases and decreases volume (in all modes). SEARCH ) Moves preset channels up and down. Moves tracks up and down. When pressed and held for 1 second: Fast-forward/ fast-backward. PLAY/PAUSE A. Turns mute on and off. Switches between playback and pause. MUTE .. Turns mute on and off. Switches between playback and pause. ISR .. Recalls ISR radio station in memory. Press and hold for more than 2 seconds: Stores current station into ISR memory (radio mode only). DISP .. Switches among main display, sub display and clock display. SCAN PS/AS °. Preset scan. When pressed and held for 2 seconds: Auto store. Scan play. RPT BLS ¤. No function. Repeat play. RDM MONI ¦. No function. Random play. *Some of the corresponding buttons on the source unit and remote control unit have different functions. E glis DB415 8. OPERATION Note: • Be sure to read this chapter referring to the front diagrams of chapter 2. CONTROLS on page 3 (unfold). English Basic Operations CAUTION When this unit is turned on, starting and stopping the engine of a car with its volume raised to the maximum level may harm your hearing. Be careful about adjusting the volume. Turning ON the Power and Adjusting the Volume 1) Press the POWER button 3. * To turn off the power, press the POWER button 3 for 1 second or longer. 2) Press the FNC button 3 and select another operation mode. Every time the FNC button 3 is pressed, the display changes the operation mode as: Radio U CD U Radio Notes: • The operation mode not connected to the unit will not be selected. • If the CD mode is selected when no disc is inserted, the display shows “NO DISC”. 3) Turning the Rotary knob # clockwise increases the volume; turning it counterclockwise decreases the volume. * The volume level is from 0 (minimum) to 33 (maximum). Audio Mode Adjustments Press the A-M button 2 to select the adjustment mode. The mode switches as follows each time the A-M button is pressed: BASS U TREB U BAL U FAD U Previous mode Adjusting the Bass 1) Press A-M button 2 and select “BASS”. 2) Turning the Rotary knob # clockwise emphasizes the bass; turning it counterclockwise attenuates the bass. * The factory default setting is “0”. (Adjustment range: –6 to +6) 3) When the adjustment is complete, press A-M button 2 several times until the function mode is reached. Adjusting the Treble 1) Press A-M button 2 and select “TREB”. 2) Turning the Rotary knob # clockwise emphasizes the treble; turning it counterclockwise attenuates the treble. * The factory default setting is “0”. (Adjustment range: –6 to +6) 3) When the adjustment is complete, press A-M button 2 several times until the function mode is reached. Adjusting the Balance 1) Press A-M button 2 and select “BAL”. 2) Turning the Rotary knob # clockwise emphasizes the sound from the right speaker; turning it counterclockwise emphasizes the sound from the left sp...