Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit difference from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. If necessary, you should consult your dealer or experienced radio/television technician for additional suggestions. You may find helpful the following booklet, prepared by the Federal Communications Commission: How to Identify and Resolve Radio-TV Interference Problems. This booklet is available from the United States Government printing office, Washington, D.C. 20402. The booklet number is 004-000-00345-4. Note: Changes or Modifications not expressly approved by the party responsible for compliance could void the users right to operate this equipment. Peripheral used in conjunction with this equipment must be connected via shielded interface cables. Use of unshielded interface cables may result in interference to radio and TV reception, and may void the user’s right to operate this equipment. 3 CONTENTS RADIO & TELEVISION INTERFERENCE 3 INTRODUCTION 5 ACCESSORIES SUPPLIED 6 ADDITIONAL ACCESSORIES FOR REMOTE CONTROL ADAPTOR 7 REAR PANEL 8 FRONT PANEL 9 INFRARED REMOTE CONTROL HANDSET 10 SYSTEM SETUP 14 OPERATION 21 CONNECTING TO A TV MONITOR 22 CONNECTING TO A VIDEO PROJECTOR OR TV/ MONITOR WITH 23 COMPONENT VIDEO 24 WHAT CAN YOU DO WITH THE GREEN GARD? INSTALLING THE GREEN CARD 25 SPECIFICATIONS 27 Q&A 28 4 Introduction Using inexpensive recordable CD’s (CD-R’s) you may play up to 99 tracks of a video CD or you may present up to nineteen tracks of full motion video and a ‘video attract loop’ that plays continuously until another track is selected. The selected track plays only one time, then the system returns to play the attract loop until another switch is pressed. CP-100 PRO replaces existing VHS or laser disc presentation hardware solutions. Compared to DVD menu driven players, it is easier to work with and has a lower media cost. CP-100 PRO is a stand-alone unit with a built in standard IDE-CD-ROM, that can be exchanged to DVD-ROM to playback standard DVD’s. The unit is compact in size and is easy to install. It is especially designed for commercial and educational uses for high quality video and audio. If you do change the drives from CD to DVD, not all of the remote functions will work the same way and the unit may require a firmware update. Please contact your local Datavideo office to discuss your requirements. Typical Applications: Trade shows – video presentations with simple or sophisticated interfaces. Hotels – A low cost solution to assist the maitre’d in telling about nearby attractions, restaurants, transportation, theaters, etc. Schools – Student productions and presentations Museums – kiosks, exhibits, etc. Get more communication value for your budget. Messages can be changed for the cost of changing the video and a 30-cent recordable CD. You can use motion sensors, floor pressure switches, broken light beam switches, etc., to begin a selected track. Corporate – Segment your benefits program and have employees watch the information that they must have. Realtors – Make an attract loop that sells your company and then select video tours of the most likely properties. Give the prospect the CP-100 PRO and let them watch it at home with the family. Medical – Non-invasive video recordings traditionally stored on VHS may be created on inexpensive recordable CD’s. The CP-100 PRO is an excellent review station. 5 Accessories Supplied Infrared Remote Control Handset 2 x “AAA” Batteries for the Handset Power Supply Power Cord 3 Phono (RCA) to 3 Phono (RCA) Audio/Video Cable 6 Additional Accessories for Remote control Adaptor With the optional Momentary Contact Switch Card, all you do is connect switches and a 9-pin cable to the Remote Adaptor (RMC-60). Momentary Contact Switch Card for connecting up to 20-switches for your own Kiosk interface Kiosk Remote Adapter (RMC-60) D-Sub 9-Pin to 9-Pin cable for connecting Momentary Contact Switch Card to the Remote Adaptor (RMC-60) 7 Rear Panel 1 7 3 5 2 6 4 1. Power Switch To switch the power on and off 2. Main DC Power Cord connecting socket To connect to the main AC power adaptor 3. Component Video Output Component Y.U.V. or R.G.B.video signal output. Although there are multiple outputs you can only use one output at a time. If you use more than one simultaneously the output signal level will be reduced. 4. External Switch Remote Interface Connect an external Datavideo Remote Adaptor (RMC-60). Support up to 20switches for your own Kiosk inter...