Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
All the products with such a slot as this are equipped with a system which automatically measures the size of an inserted medium. That’s why both standard-size “Memory Stick” and smaller “Memory Stick Duo” can be used on this product without any Memory Stick Duo Adaptor. • Do not insert multiple “Memory Sticks” at the same time. It might cause damage to the product. • When you use “Memory Stick Duo” on this product, please make sure to insert it in the right direction. • “Memory Stick Duo” should be kept away from small children to prevent them from accidentally swallowing it. • When you use “Memory Stick Micro” on this product, please make sure to attach the medium into M2 adaptor. If you attempt to insert “Memory Stick Micro” without attaching to M2 adaptor, there is a possibility that it cannot be pulled out. Usage Notes “Memory Stick” Media Notes on using “Memory Stick” media Terminal Write- Protected switch Label area • Do not remove “Memory Stick” while data is being read or written. • Data may be damaged if: – You remove “Memory Stick” or disconnect the USB cable while data is being read or written. – You use “Memory Stick” in a place where it is susceptible to static electricity or electric noise. • You can keep backup copies of important data on a “Memory Stick.” • Avoid touching the metal terminals on the “Memory Stick” to prevent damage from static discharge. • Do not subject the “Memory Stick” to excessive stress or shock. • Do not disassemble or modify “Memory Stick.” • Keep “Memory Stick” and other media away from water, excessive heat and humidity, and from corrosive elements. • Do not use or keep “Memory Stick” under an unfavorable condition as below: – Extremely hot place (such as in a parked car with windows closed in summer, a spot under direct sunlight, or near an electrical appliance that radiates heat). – Humid place. – Place near corrosive substances. • If you set Write-Protected switch “LOCK,” data cannot be recorded, edited, or erased. • Do not stick anything other than the supplied labels on the label area of “Memory Stick.” • Stick a label precisely within the label area. Make sure that the label does not go beyond the area. • Carry and keep “Memory Stick” in the supplied case. Notes on using “Memory Stick Duo/ Memory Stick PRO Duo” Terminal Write- Protected switch Memo area • When you use “Memory Stick Duo/ Memory Stick PRO Duo” without Write- Protected switch, be careful not to edit or erase important data by mistake. • When you use “Memory Stick Duo/ Memory Stick PRO Duo” with Write- Protected switch, data cannot be recorded, edited, or erased by “LOCK” the switch. • Use an object with a sharp tip to move the Write-Protected switch. • Do not press on the memo area strongly when writing. • Carry and keep “Memory Stick” in the supplied case. SmartMedia Cards Supported SmartMedia cards The reader/writer supports 3.3-volt and 3volt SmartMedia cards, but not the older 5volt type. Notch 3.3 V and 5 V type 3 V type Note Do not insert a 5-volt SmartMedia card into the reader/writer forcibly. SmartMedia card handling If the gold contact area of a SmartMedia card is dirty, a read error may occur. Keep the contact area clean. Otherwise do not touch the gold contact area. Do not twist or warp the card. Protect the card from static electricity. SmartMedia card with ID The reader/writer does not support the ID information on SmartMedia cards, but allows any SmartMedia card with an ID to be used as regular media. Other Points to Note Media formatting Do not format (initialize) memory cards with a computer. If you format a memory card with a computer, devices such as digital cameras may not be able to use it due to differences in format type (FAT size, cluster size, hard disk type, or super floppy disk type). If you use a digital camera, format memory cards with your camera, instead. Restrictions on DOS mode In Windows, the reader/ writer does not operate in DOS mode. To use the reader/writer, start up Windows. Standby The reader/writer supports standby functions based on the PC2000 standard, which may not cover the standby function of all computers. Disable the standby function of your computer if it causes any problems. While the computer is in standby, do not insert or remove any media. Antivirus software If you have memory-resident antivirus software on your computer, the computer may hang or become unusually slow. In this case, set your antivirus software so it does not scan the media in the reader/writer. Do not attempt to dismantle, repair, or alter the reader/writer yourself Do not, under any circumstances, attempt to dismantle, repair, or alter the reader/writer yourself. You may not only permanently damage the reader/writer and/or your computer, but may also cause fire or personal injury through electrical shock. Operating and storage environments • Do not place the reader/writer close to heat sources or in direct sunlight; in dusty, dirty, or humid locations; under precipitation suc...