Stimmen - 5, Durchschnittliche Bewertung: 4.8
(
)
)
|
Anleitung Zusammenfassung
If the buffer is empty, it waits at the address and then restarts recording after the buffer is full. You can avoid Buffer Under-Run problems by applying the above-mentioned principle. Recommended Disc Types CD-R MCC, PRO, TDK, FUJI, SKC, MAXELL, MPO, BEALL CD-RW RICOH, SONY, MITSUBISHI, NANYA General DMA Installation Guide Windows 98/Me Important! Please read the entire DMA installation guide before installing your COMBO drive. About DMA Installation For stable writing performance at high speeds, Installation of DMA transfer mode for E-IDE/ATAPI interface is strongly recommended. We recommend DMA mode for fast writing. DMA Setting Before you install your COMBO drive, we recommend to set DMA to enabled on your PC system. See the following procedure to set DMA transfer mode in windows oprerating system. (Windows 98/ME) + Click on START + Select your CD-R/RW drive + Click on Settings + Click on the Properties button + Select Control Panel + Click on the Settings tab + Select the System Icon + Check the DMA checkbox to enables DMA. + Select the Device Manager panel + Click OK in System Properties + Restart your PC + Expand the CD-ROM icon Windows 2000/XP Select the DMA mode by selecting [Start > Setting > Control Panel > System > Device Manager > IDEATA/ATAPI Controller > Default/Assistant IDE Channel Advanced Information] Troubleshooting Problem Meaning / Solution The COMBO drive is not detected by the computer. After installing the COMBO drive, the PC gets slower. Check that the power, audio and IDE cables are correctly connected to the computer. Change the IDE cable and reconnect it to the computer. Preferably, connect a second IDE cable to the COMBO drive in master mode. Check the position of the jumper in the master/slave select terminal. The COMBO drive is not recognized by MS-DOS. Reinstall the device driver or update it with the latest version by downloading it from the Samsung Web site. -Http://samsung.com -The COMBO drive is not detected by Windows. This case may occur when there is a Windows installation problem; reinstall Windows. No sound is heard from an audio CD. Check whether the audio cable is correctly connected to the sound output terminal on the COMBO drive and the sound card CD-IN terminal. Check that the sound card is operational. Adjust the volume control. Run the CD player supplied with Windows or your sound card. You can listen to the CD by connecting headphones to the appropriate connector. A CD is not read or is read too slowly. Check whether the CD is of good quality and clean it, if necessary. The disc compartment will not open. Check that the power cable is correctly connected. Power off and disconnect the PC. Insert a pin or unfolded paper clip in the emergency hole and push firmly until the disc compartment opens. When the MPEG software plays a Video CD, the picturesare not regular and the runningspeed is too slow. Adjust the size of the replay screen. After checking the display resolution, adjust it, if necessary. The Disc is not in message is displayed even though a dischas been inserted. The computer may not recognize the disc if you start playback too quickly after inserting the disc. Open and close the disc compartment and try again. Clean the disc and try again. The COMBO drive is not detected after it is connected to a sound card. The interface mode of the sound card is AT-BUS. You must therefore connect the COMBO drive to the IDE port on the PC mother board, rather than to the sound card, or install an E-IDE compatible sound card. Troubleshooting Troubleshooting SAMSUNG continually strives to improve its products. Both the design specifications and these user instructions are thus subject to change without notice. Technical Specifications *Note) The SM-352BB/XRA model does not support DVD-RAM disc. ITEM CD-RW DVD/CD DISC Disc types supported in read mode DVD-ROM, DVD-RAM, DVD-VIDEO, DVD-R, DVD - RW, CD-DA (Audio), CD-ROM, CD-ROM XA, CD-Plus, CD-Extra, Photo-CD (Single, Multi-session), Video CD ready, Enhanced CD, CD-I/FMV, CD-R, CD-RW, CD-TEXT Erasing disc types CD-RW Disc diameter 120 mm or 80 mm DRIVE PERFORMANCE Data transfer rate Recording CD-R: 1200 KB/sec. (8X), 2400 KB/sec. (16X), 3600 KB/sec. (24X), 4800 KB/sec. (32X), 6000 KB/sec. (40X), 7200 KB/sec. (48X), 7800 KB/sec. (52X) CD-RW : Ultra Speed Writing DISC: 2400 KB/sec. (16X), 3600 KB/sec. (24X), High Speed Writing DISC: 1500 KB/sec. (10X), Low Speed Writing DISC: 600 KB/sec. (4X), Reading CD/CD-R: CAV 52 DVD: CAV 16 Multiword DMA mode 2:16.6MB/sec Ultra DMA mode 2:33.3MB/sec Access time 130ms 130ms/110ms Data Buffer 2MB Laser Semiconductor laser Slide mechanism Stepping motor Spindle motor Brushless motor Load mechanism Tray. DC motor (Soft Eject). Horizontal/Vertical. ERROR RATE Mode 1: 1 block/10-12 , Mode 2: 1 block/10-9 FRONT PANEL Eject button Auto eject or Auto inject Indicator If the Power is ON/BUSY, this means the disc is loaded. Green: Reading/Recording Status Headphone output...