Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
LASER STANDARD IEC 60825-1 : 1993 + A1 : 1997 + A2 : 2001 BG68-00787A Rev.01 - - Installing the Drive Installing the CD-Rom Drive If necessary, attach a horizontal bracket to both sides of the drive. You can purchase these accessories separately from your computer dealer. (Screws for use: M3 X 6 X 4) 1 Remove the plate from a free expansion slot and install the CD-ROM drive, as shown in the illustration. If you have no free expansion slot, install the drive in place of the diskette drive. Make sure to use the standardized screws supplied (M3X6). - To use screws other than M3X6 may result in malfunction. System Requirements Intel Pentium 166MHz(or higher), 16 MB of RAM (or higher) with an EIDE interface, Windows 98 / 2000 / ME / XP Windows NT 4.0 (or higher) 2 How to install the CD-ROM drive on your PC. First, remove the cover; connect the cable to the CD-ROM drive and then to the PC. CD-Rom Drive Horizontal Bracket Plate Using the Drive/Storing and Cleaning Your Discs 1 Push the power button and boot the computer. After booting the computer, open the disc compartment by pressing the Eject button. 2 Insert the disc (CD) with the label on the disc facing upwards and close the disc compartment by pressing the Eject button. The indicator light comes on. 3 4 Play the disc (CD). Using the CD-ROM Drive Do not place a disc in direct sunlight. Store a disc vertically in a well-ventilated and stable location. Do not write or attach a label on a disc. Do not drop a disc or place heavy objects on it. Do not touch the surface of a disc; hold it by the edges. To clean a disc, polish lightly from the inside of the disc to the outside with a soft cotton cloth. Storing Your Discs Cleaning Your Discs Run the CD player program supplied with the sound card or play the Windows Media Player. Playing CD-DA/Audio CDs Follow the instructions provided with the disc. A video card or MPEG software and a sound card need to be installed to view video CDs. Playing Video CDs The disc may not function properly if there are fingerprints, foreign substances or dust on the disc surface. If the drive is vertically installed, you cannot use an 8 cm MiniDisc because the disc is movable. Solving Technical Problems The CD-ROM drive is not detected by the computer. After installing the CD-ROM drive, the PC gets slower. Check that the power, audio and EIDE cables are correctly connected to the computer. Change the EIDE cable and reconnect it to the computer. Preferably, connect a second EIDE cable to the CD-ROM drive in master mode. Check the position of the jumper in the master/slave select terminal. The CD-ROM drive is not recognized by MS-DOS. Reinstall the device driver or update it with the latest version by downloading it from the Samsung Web site. - - The CD-ROM drive is not detected by Windows. This case may occur when there is a Windows installation problem; reinstall Windows. No sound is heard from an audio CD. Check whether the audio cable is correctly connected to the sound output terminal on the CD-ROM drive and the sound card CD-IN terminal. Check that the sound card is operational. When the MPEG software plays a Video CD, the pictures are not regular and the running speed is too slow. Adjust the size of the replay screen. After checking the display resolution, adjust it, if necessary. A CD is not read or is read too slowly. Check whether the CD is of good quality and clean it, if necessary. The disc compartment will not open. Check that the power cable is correctly connected. Power off and disconnect the PC. Insert a pin or unfolded paper clip in the emergency hole and push firmly until the disc compartment opens. The CD-ROM drive is not detected after it is connected to a sound card. The interface mode of the sound card is AT-BUS. You must therefore connect the CD-ROM drive to the EIDE port on the PC mother board, rather than to the sound card, or install an EIDE compatible sound card. The Disc is not in message is displayed even though a disc has been inserted. The computer may not recognize the disc if you start playback too quickly after inserting the disc. Open and close the disc compartment and try again. Clean the disc and try again. The friction noise generated during SPIN-UP and STOP is caused by the Automatic Ball Balancing System(ABS) and is not a malfunction. Technical Specifications 6 7 8 9 Failure to do so may cause the device to fall onto a hard surface, resulting in damage or malfunction. 52X, 7800KB/s(MAX) SECTIONS SH-152 DISC DRIVE PER - FORMANCE FRONT PANEL REAR PANEL OPERATING ENVIRONMENT General reliability ERROR RATE Disc types supported Disc diameter Data transfer rate Access time (typical) Data buffer capacity Laser Slide mechanism Spindle motor Load mechanism Eject button Indicator(LED) Required power Interface connector Audio output Jumper block Storage area Work area Net weight MTBF CD-DA, CD-ROM Mode-1, CD-ROM XA ...