Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
• Is the proper value(s) set in the network setting? Check “Communication Setup”. (Pages 46–49) Cannot download BD-LIVE contents. • Is the LAN cable or the wireless LAN adapter connected properly? (Pages 18–19) • Is the USB memory device properly connected? Check that the USB memory device is connected to the USB1 or USB2 terminal of this Player. (Page 27) • Check if the BD disc supports BD-LIVE. • Check the setting for “BD Internet Access”. (Page 44) Appendix (Continued on the next page) Troubleshooting Other Problem Possible causes and solutions The TV operates incorrectly. • Some TVs with wireless remote control capability may operate incorrectly when using the remote control of this Player. Use such TVs away from this Player. The Player heats up during use. • When using this Player, the console cabinet may heat up depending on the usage environment. This is not a malfunction. POWER (ON/STANDBY) indicator will remain lit. • When the AC cord is removed from the outlet, the POWER (ON/STANDBY) indicator will remain lit for a short period. This is normal and is not a malfunction. To Reset this Player POWER • If this Player receives strong interference from a source such as excessive static electricity, strong external noise, malfunction of power supply, or voltage caused by lightning during use or a wrong operation is sent to the Player, errors like the Player not accepting an operation may occur. Press and hold POWER on the Player until “ ” appears on the front panel display when the Player does not operate properly even after the power has been turned off. Then, after the POWER indicator is lit, turn on the power. • When a reset is performed while the power is on, the Player will turn off. Turn the power on again. At this point, it may take a few moments for the system processing to finish before the Player is ready for use. During the system processing, the BD/DVD/CD mode indicator on the front panel display of the player will blink. Once the system processing has finished, the indicator will finish blinking and then light up normally. You can operate the Player when the BD/DVD/CD mode indicator is lit. • Since all settings including the language setting stored in memory are also reset when a reset has been performed, they must be set again. • When the problem persists even after performing a reset, unplug the AC cord and plug it in again. If this does not solve the problem, contact the nearest service center approved by SHARP. On-screen Error Messages The following messages appear on the TV screen in case of an error during operation. Error message Possible Error Suggested Solution Cannot play. • The disc cannot be played back with this Player. • Check the disc, and load it correctly. Incompatible disc. • If you load a disc which cannot be played with this Player (i.e. a scratched disc), or if you load a disc upside down, this message will appear, and the disc tray will automatically pop out. • Occurs if the loaded disc cannot be played because it is a non-standard disc or scratched, etc. • Remove the disc. Cannot operate. • Occurs if an operation is incorrect. — This USB memory is not formatted properly. Please format the memory in USB memory management. • Occurs if there is a formatting error. • Occurs if the USB memory is not formatted with FAT 32/16. • Format the USB memory again. • Format the USB memory with your PC. The Connected USB Memory cannot be used. It should be compliant with USB 2.0 • Occurs if USB memory not compliant with USB 2.0 High Speed (480Mbit/s) is used (i.e. USB 1.0/USB 1.1). • Connect USB 2.0 High Speed (480Mbit/s) compliant USB memory. Appendix Specifications Specifications are subject to change without notice. General Power supply AC 120 V, 60 Hz Power consumption (Normal) 15 W Power consumption (Standby) 0.3 W (When “Quick Start” is set to “No”) Dimensions Approx. 16 15/16 g1 15/16 g7 13/16 inch (W gH gD) Approx. 430 mm g58 mm g198 mm (W gH gD) Weight Approx. 3.86 lbs. (1.75 kg) Operating temperature 41°F to 95°F (5°C to 35°C) Storage temperature –4°F to 140°F (–20°C to 60°C) Operating humidity 10 % to 80 % (no condensation) TV systems NTSC system Playback Playable discs/media formats BD-ROM, BD-RE, BD-R, DVD Video, DVD+RW/+R/-RW/-R (Video/VR/AVCHD/JPEG file/MP3 file/DivX (H.264/MKV) format), Audio CD (CD-DA), CD-RW/R (CD-DA/JPEG file/MP3 file format) USB memoy device (JPEG file/MP3 file/DivX (H.264/MKV) format) Region code A or ALL for BD, 1 or ALL for DVD Input/Output HDMI HDMI 19-pin standard connector (1080p 24Hz output) HDMI® (Deep Color, x.v.Color, Dolby TrueHD, DTS-HD Master Audio | Essential) Digital audio optical output Terminal: Square Optical terminal USB input USB1/USB2 USB 2.0 High Speed (480Mbit/s) correspondence (for Wireless LAN adapter and Local storage/Software update/JPEG, MP3 and DivX (H.264/MKV) playback) ETHERNET 10BASE-T/100BASE-TX Specifications Wireless LAN USB Adapter Product name Wireless LAN adapter (supplied) Standard IEEE 802.11b/g/n Host interfa...