Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
No reply from host. Please check the connection or router settings. .If you use a hub, then check the connection between the hub and the router. –Use the UPLINK port of the hub to connect to a router. –If the hub’s Link lamp does not light up, then check the cable connection, LAN terminal connection, cable itself (a cross over cable may have been used by mistake), etc. .Check the “IP Address”, “Subnet Mask”, and “Default Gateway” in the “IP Address/DNS Settings”. .If the MAC address information is required, then press [SETUP] to display the “Network” menu. 16 17 17, 35 Network connection refused. Please confirm Setup“BD-Live Internet Access.” .When you set “BD-Live Internet Access” to “Allow (Limited)” and play BD-Live contents which do not have a content owner certificate, the Internet access of the content is not allowed. If you allow the content to connect to Internet, set “BD-Live Internet Access” to “Allow (ALL)”. 32 Unable to check for latest firmware version. Please try again later. .The firmware download server is currently unavailable. Please try again later. — 38 RQT9412 On the unit’s display Page F99 .The unit fails to operate properly. Press [POWER I/I] on the main unit to switch the unit to standby for 3 seconds. Now press [POWER I/I] on the main unit again to turn the unit on. — HDMI ONLY .Some BD-Video discs can only be output with HDMI. — NET .Displays while VIERA CAST is starting up. — No PLAY .There is a viewing restriction on a BD-Video or DVD-Video. 32 No READ .The media is dirty or badly scratched. The unit cannot play. — PLEASE WAIT .The unit is carrying out internal process. This is not a malfunction. You cannot operate the unit while “PLEASE WAIT” is displayed. .When connected to TV(VIERA) with “HDAVI Control 4”, and power supply is turned off by the “Auto power stand-by” function on the TV side. — — REMOVE .The USB device is drawing too much power. Remove the USB device. 19 SET . (“ .” stands for a number.) .The remote control and main unit are using different codes. Change the code on the remote control. Press and hold [OK] and the indicated number button at the same time for more than 5 seconds. 36 UNFORMAT .You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL or DVD-RW (DVD-Video format). — UNSUPPORT .You have inserted a media the unit cannot play. .You tried to operate with a non-compatible USB device. 6, 7 7 U11 .The video head is dirty. Perform the cleaning. — U59 .The unit is hot. The unit switches to standby for safety reasons. Wait for about 30 minutes until the message disappears. Select a position with good ventilation when installing the unit. Do not block the cooling fan on the rear of the unit. — U72 U73 .The HDMI connection acts unusually. –The connected equipment is not HDMI compatible. –Please use HDMI cables that have the HDMI logo (as shown on the cover). –The HDMI cable is damaged. — H.. or F.. .There is something unusual. (The service number displayed after H and F depends on the unit’s condition.) .Check the unit using the troubleshooting guide. If the service number does not disappear, do the following. 1 Disconnect the plug from the AC outlet, wait a few seconds, then reconnect it. 2 Press [POWER I/I] to turn the power on. (The unit may be fixed.) If the service number does not disappear despite doing the above, request service from the dealer. Inform the dealer of the service number when requesting service. — 40–43 START .The system is being restarted during the firmware update. Please do not turn off power. 16 UPD./. .The firmware is being updated. 16 FINISH .The firmware update is complete. 16 Reference 39 RQT9412 Troubleshooting guide Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the chart do not solve the problem, refer to “Customer Services Directory (United States and Puerto Rico)” on page 46 if you reside in the U.S.A.and Puerto Rico, or refer to “Product information” on page 45 if you reside in Canada. The following do not indicate a problem with this unit: .Regular disc rotating sounds. .Image disturbance during search. To reset this unit Page To restore the unit if it freezes due to one of the safety devices beingactivated To return all settings to the factory preset To return to the factory preset(No setting) .Press and hold [POWER I/I] on the main unit for 3 seconds. (The settings remain unchanged.) .Select “Yes” in “Restore Default Settings” in the Setup menu. This returns all values in the Setup menu and the on-screen menu, except for “Remote Control Code”, “On-screen Language”, “IP Address/DNS Settings”, “Proxy Server Settings”, “DVD-Video Ratings”, “BD-Video Ratings” and “Network Service“ to the default settings. .Reset the unit as follows: 1Press [POWER I/I] on the unit to turn off the unit. 2 Press and hold [;], [POWER I/I] and [< OPEN/CLOSE] on the unit at the same time for more than 5 seconds until “HELLO” is displayed on the unit...
Dieses Handbuch ist für folgende Modelle:Blu-Ray Player - DMP-BD70V (3.96 mb)