Stimmen - 4, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
2. Place the slushie chamber onto the motor base, ensuring that the slushie chamber sits flush onto the drive mechansim (see fig. 1) . fig. 1 3. Insert the ice chamber into the slushie paddles, then insert the ice paddles into the ice chamber (see fig. 2) . fig. 2 The locking at the top of paddles should easily snap into the top of the slushie paddles (see fig. 3) . 4. Place the ice chamber assembly into the slushie chamber, ensuring that the ice chamber assembly sits flush onto the drive mechanism at the base of the slushie chamber (see Fig 4) . 5. Pour 60ml ( 1. 4 cup) of water into the ice chamber. Place 1 layer of ice cubes into the ice chamber until it is approximately half full. Add 1 ice chute cap of rock salt or coarse sea salt to the ice cubes (see fig. 5) . Continue to layer ice and salt until fig. 3 fig. 4 fig. 5 approximately 2.5cm below the rim of the ice chamber. This allows more ice and salt to be added if required. Note: Medium-sized square ice cubes work well in the ice chamber. 5 6. To secure the lid onto the slushie chamber, align the front of the lid with the front of the slushie chamber and firmly push down the rear of the lid until it locks into fig 6 position (see fig. 6) . Place the ice chute cap into position in the lid. 7. Plug the power cord into a 240v power outlet and switch on. 8. Ensure that slushie dispenser is in the closed position to avoid spillage. 9. Move the On/Off/Pour switch up to the ‘On’ position. The ice chamber and slushie paddles will begin to rotate. 10. Slowly pour the prepared slushie ingredients through the lid opening located at the rear of the lid (see fig. 7) . The liquid will flow into the slushie chamber fig 7 and be rotated by the slushie paddles and chilled by the ice chamber. Note: Do not exceed the “FILL MAX” line on the slushie chamber. 11. Allow the Slushie Factory to operate for approximately 20 minutes, depending on the slushie ingredients or 6 until the mixture reaches the consistency. Do not turn the Factory off during use as may thaw. 12. Add more ice cubes and salt if necessary through the ice chute. Note: Layer ice and salt until approximately 2.5cm below the rim of the ice chamber. Exceeding this may cause overflowing and the slushie ingredients may become contaminated with salt. 13. When ice peaks form against the paddles in the slushie chamber, the slushie ingredients have reached the desired consistency. Place a serving glass onto the drink tray, then turn the slushie dispenser clockwise to the ‘Pour’ position. Move the On/Off/Pour switch down to the ‘Pour’ position (see fig. 8) . The ice chamber fig 8 and slushie paddles will rotate to assist with dispensing. 14. To stop dispensing, turn the slushie dispenser anti-clockwise to the ‘Close’ position and move the On/Off/Pour switch to the ‘Off’ position. 15. Wait until the paddles have stopped rotating before removing the lid or slushie chamber from the motor base. Note: If any moisture or liquid appears on top of the motor base, ensure the Slushie Factory is switched off by moving the On/Off/Pour switch to the ‘Off’position, then switch off at the power outlet and unplug Remove the slushie chamber from the motor base. Wipe the motor base immediately with and check that the Slushie Factory is correctly assembled. DISASSEMBLING FACTORY FOR CARE AND CLEANING Always ensure the Slushie Factory is switched off by moving the On/Off/Pour switch to the ‘Off’ position, then switch the appliance off at the power outlet and unplug the cord before cleaning. 1. Remove the slushie chamber from the motor base. 2. Remove the lid by depressing the latch and lifting upwards. 3. Remove the ice chamber assembly from the slushie chamber. 4. Discard the ice water and salt from the ice chamber. 5. Carefully lift locking latches from the ice paddles and disassemble the ice chamber assembly. 6. To clean the slushie chamber, fill with warm soapy water and open the slushie dispenser to allow clean water to run through. Use a small, flexible bottle brush to clean the inside of the slushie dispenser 7. Wash the lid, ice chute cap, slushie paddles, ice paddles and ice chamber in warm, soapy water and dry thoroughly. This must be done after each use to avoid salt corrosion especially on the ice chamber. 8. Wipe the motor base with a soft damp cloth. Dry thoroughly. Note: Do not wash any part of the Slushie in the dishwasher. Hand wash only. Do not immerse the motor base or any other liquid. Do not use chemical, steel wool, or abrasive cleaners to clean any parts of the blender. STORAGE Ensure the appliance is switched off and unplugged from the power outlet. Ensure all parts are clean and completely dry before reassembling. Store the assembled Slushie Factory upright on a level surface. Do not place any heavy objects on top of the Slushie Factory during storage. 7 RECIPES Hints and Tips Each of the recipes below are for approximately 500ml to give you the option of serving size. Make a maximum of 1 litre by doubling the...