Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
Rinse and dry thoroughly. Use a damp cloth to wash over the mixer base and the hand mixer. Dry with a soft cloth. NEVER immerse the base stand or the hand mixer in water or any other liquids. 2. Before assembling your Convertible Hand/Stand Mixer, make sure that the power cord is unplugged from the electrical outlet and that both the speed control and the base speed control dial are in the “ OFF” position. 1. Ensure that the hand mixer is not plugged in to an electrical outlet and that the speed control switch is on the “ 0” (off) position. 2. Insert the beaters into the sockets on the under side of the hand mixer and twist counter clockwise until the beater is firmly fitted into the socket. 3. To release the beaters from the unit, press on the beater eject button on the front of the unit and they will pop out. (Fig. 1) Warning: To avoid injury when inserting or removing beaters or dough hooks, always set the speed selector on “ 0” and unplug the appliance. Attaching the Beaters to the Hand Mixer 1. Ensure that the hand mixer is not plugged in to an electrical outlet and that the speed control switch is on the “ 0” (off) position. 2. The dough hooks have a set method of fitting into the hand mixer because they are not identical. One has a grommet and the other does not. (Fig. 2) Attaching the Dough Hooks to the Hand Mixer Press eject button Fig. 1 Grommet 3. Looking at the under side of the hand mixer, you will see that one of the sockets has a red dot over it. (Fig. 3) Insert the dough hook with the grommet into this socket. Grommet 4. Then insert the other dough hook into the other socket. Push both dough hooks in until you hear a click confirming that they are securely in place. 5. To release the dough hooks from the unit, press on the beater eject button on the front of the unit they will pop out. (Fig. 1) Note: Ensure that the beaters or dough hooks are fully inserted into the correct sockets your mixing results may be affected. Fig. 2 Fig. 3 OPERATING INSTRUCTIONS 1. Press the tilt button, located on the top of the support pivot . While the button is depressed, ease the support pivot back. (Fig. 4) Assembling the Hand Mixer to the Stand Warning: To avoid injury when assembling the hand mixer to the stand, always set the speed selector on “ 0” and unplug the appliance. Support Pivot Fig. 4 Tilt Button The support pivot will lock into this raised position until it is released by pressing the tilt button again. 2. To connect the hand mixer to the support pivot, locate the two retaining prongs on the support pivot into the two rectangular holes in the heel of the hand mixer. (Fig. 5) When the hand mixer is seated on the support pivot, press down on the hand mixer to click it into place and lock the hand mixer and the support pivot together. Fig. 5 Rectangular holes Retaining prongs Support pivot Note: Ensure that the two retaining prongs on the support pivot are fully connected into the hand mixer. 3. While the hand mixer is still in the raised position, insert either the beaters or the dough hooks. 4. To lower the hand mixer, press and hold the tilt button with one hand while holding the hand mixer with the other hand and slowly lower the hand mixer down. (Fig. 6) Press the tilt button and tilt the hand mixer down Fig. 6 5. To remove the hand mixer from the pivot support, first raise the mixer by pressing the tilt button and raise the mixer up. (Fig. 7) the mixer will lock into the raised position. 6. Then press the mixer release button which is located on the under side of the pivot support with one hand and with the other lift the hand mixer by the handle upwards and away from the support pivot. (Fig. 8) Press the tilt button and tilt the hand mixer up Fig. 7 Hand mixer release button Fig. 8 4 OPERATING INSTRUCTIONS 1. Place the base of the mixing bowl onto the turntable of the stand. To fully lock the mixing bowl in place, press down and turn the mixing bowl in a clockwise direction until you hear it click into place. (Fig. 9) Fitting the Bowl onto the Turntable of the Stand Warning: To avoid injury when assembling the hand mixer to the stand, always set the speed selector on “ 0” and unplug the appliance. 1. Before plugging the hand/stand mixer into the electrical outlet, assemble the unit with the desired accessories. 2. Set the speed selector switch to the “ HI” or “ LO” position. 3. Select the speed that you desire. Fig. 9 5 2. To remove the mixing bowl from the stand, press down and turn the mixing bowl counter clockwise. The mixing bowl can now be detached from the turntable and lifted away. (Fig. 10) Fig. 10 Note: It is easier to fit the mixing bowl to the turntable when the hand mixer is not attached to the pivot support. Using the Convertible Hand/ Stand Mixer Warning: To avoid injury when assembling the hand mixer to the stand, always set the speed selector on “ 0” and unplug the appliance. MIXING GUIDE MIXING TASK RECOMMENDED SPEED(S) Folding & Blending “LO” 1 & 2 Light Mixing “LO” 3 & 4 Cr...