Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Cuisinart Dateigröße: 201.38 kb Dateiname: e29d7142-b648-5654-815e-a6ad22688583.pdf Unterrichtssprache:

2 22. ..Make sure the Stop (2) is loose. 3 33. ..Move the Vise Assembly (5-9 & 15) to the rear position on the arm of the Mounting Plate. 4 44. ..Screw the Round Die Mounting Shaft (28) into the Mounting Plate. 5 55. Set the Round Die (29) onto the Mounting Shaft. 6 66. Move the Bending Block Assembly (16, 17, 22-24) back all of the way. You may have to release the Bending Block Locking Plate (21) by loosening the two Hex Key Bolts (20). Do not secure the Locking Plate at this time. 7 77. ..Set stock against the Round Die and close the Vise so that it clamps the work securely against the Die. 8 88. ..Move the Bending Block in until it is up against the work and its Face (16) is even with the Vise Face (8). Secure the Bending Block by tightening the two Bolts. 9 99. ..Move the Bending Block to the left with the Handle (27) until you have achieved your desired angle bend, remembering to account for “spring-back”. 1 110 00. ..If you wish to do repeat bends at the same arc, tighten the Stop at the point where you finished making your bend and tighten it. 1 111 11. ..When you wish to do complete 360° rings, make sure you clamp the very end of your workpiece in-between the Vise and the Die. Bend your stock all the of the way around, and cut off the excess. 1 112 22. ..To make springs, loosen the Stop (2), and lift the stock to be formed slightly as you bend the stock around the Die. When starting and finishing the spring, make a complete 360° ring as described in Step #11. F FFi iig ggu uur rre ee 1 11. .. Die Mounting Plate Hole Location (A) Insert Round Die Mounting Shaft here (B) Insert Hex Key Bolts here (C) Insert Angle Die Spring here (D) Insert Angle Die Hex Bolt here -4- G7153 Universal Bender A AAn nng ggl lle ee O OOp ppe eer rra aat tti iio oon nns ss 1 11. ..Make sure the Die Mounting Plate (4) is attached to the Body. Refer to F FFi iig ggu uur rre ee 1 11 for the hole positions needed for Angle Operations. 2 22. ..Make sure the Stop (2) is loose. 3 33. ..Move the Vise Assembly (5-9 & 15) to the forward position on the arm of the Mounting Plate. 4 44. ..Place the Angle Die’s (13) Spring Pin (19) into the Mounting Plate’s small unthreaded hole. 5 55. ..Attach the Angle Die by screwing the Hex Key Bolt (18) into the small threaded hole of the Mounting Plate. 6 66. ..Move the Bending Block Asembly (16, 17, 2224) back all of the way. You may have to release the Bending Block Locking Plate (21) by loosening the two Hex Key bolts (20). Do not secure the Locking Plate at this time. 7 77. ..Set the stock against the Angle Die and close the Vise so that it clamps the work securely against the Die. 8 88. ..Move the Bending Block until it is up against the work and its Face (16) is even with the Vise Face (8). 9 99. ..Move the Bending Block to the left with the Handle (27) until you have achieved the your desired angle bend. Remember to account for “spring-back”. 1 110 00. ..To make repeat bends at 90°, use the Angle Gauge Assembly (10-12). Screw the Gauge Shaft (10) into the Angle Die. Slide the Gauge Stop (11) onto the Shaft to the desired position (depending upon the length of your work). This will “stop” the bend at the proper location. 1 111 11. ..If you wish to do repeat bends at the same angle (other than 90°), use the Stop (2). S SSp ppi iir rra aal ll O OOp ppe eer rra aat tti iio oon nns ss 1 11. ..Remove the Die Mounting Plate (4) by removing the two Hex Key Bolts (4). Loosen the Stop (2). 2 22. ..Retract the Bending Block Assembly (16, 17 22-24) all of the way. Remove the Face Plate (16) by unscrewing the associated Hex Key Bolt (17). This will reveal the Bending Block Wheel (22). F FFo oor rr s sst tte eep pps ss 3 33, ,, 4 44, ,, & && 8 88, ,, s sse eee ee F FFi iig ggu uur rre ee 2 22. .. 3 33. ..Attach the Spring Forming Mounting Disc (32) with two Hex Key Bolts (in position1). 4 44. .. Place the Spring Pin (25) of the Spring Forming Die “A” (31) into the hole 3 and attach the long Hex Key Bolt (26) in position 2. F FFo oor rr s sst tte eep pps ss 5 55 & && 7 77, ,, s sse eee ee F FFi iig ggu uur rre ee 3 33. .. 5 55. ..Insert the stock to be bent into the hole of Die “A”. 6 66. ..Move the Bending Block Assembly forward until it contacts the stock and tighten it in position. 7 77. ..Bend the stock until the portion being formed is about at the Pin (marked with a “P” in the figure). 8 88. ..Now put the Spring Pins (25) of Spring Forming Die “B” (30) into holes 4 & 5. 9 99. ..Finish your bend by wrapping completely around the Forming Dies. F FFi iig ggu uur rre ee 2 22 Spring Form Mounting Disc F FFi iig ggu uur rre ee 3 33 Spring Forming Die G7153 Universal Bender -5 G7153 Universal Bender Exploded Parts View -6-G7153 Universal Bender R RRE EEF FF Q QQT TTY YY D DDE EES SSC CCR RRI IIP PPT TTI IIO OON NN 1 1 BASE 2 1 STOP 3 1 BODY 4 1 DIE MOUNTING PLATE 1 VISE DRIVE SCREW 6 1 VISE HANDLE 7 1 VISE BASE 8 1 VISE FACE 9 2 HEX KEY BOLT 1 GAUGE STOP 11 1 GAUGE SHAFT 12 1 GAUGE LOCKING SCREW 13 1 ANGLE...

Herunterladen

Geben Sie zwei Ziffern: